Sony-STRV323-rec-sm维修电路原理图.pdf
MICROFILM SERVICE MANUAL FM STEREO/FM-AM RECEIVER US Model STR-DE335/SE391 Canadian Model AEP Model E Model Australian Model STR-DE335 Chinese Model STR-V323 STR-DE335/SE391/V323 SPECIFICATIONS Photo: STR-DE335 US model Audio power specifications (US model) POWER OUTPUT AND TOTAL HAR- MONIC DISTORTION With 8-ohm load, both channels driven, from 20a) 20,000 Hz, rated 100 watts per channel minimum RMS power, with no more than 0.09 %b) total harmonic distortion from 250 milliwatts to rated output. STR-SE391: a) 40Hz b) 0.5 % Amplifier section Power output Stereo modeSTR-DE335/V323 US, Canadian models: (8 ohms at 20 Hz 20 kHz less than 0.09 % total harmonic distortion) 100 W + 100 W AEP model: (DIN 1 kHz, 4 ohms) 80 W + 80 W Malaysia, Singapore, Chinese, Australian models: Rated power: (8 ohms at 1 kHz, THD 0.7 %) 80 W + 80 W Reference power: (8 ohms at 20 Hz 20 kHz, less than 0.09 % total harmonic distortion) 70 W + 70 W E model: Rated power: (8 ohms at 1kHz, THD 0.7 %) 100 W + 100 W Reference power: (8 ohms at 20 Hz 20 kHz, less than 0.09 % total harmonic distortion) 95 W + 95 W STR-SE391 (8 ohms at 40 Hz 20 kHz, less than 0.5 % total harmonic distortion) 100 W + 100 W Surround modeSTR-DE335/V323 and 5.1 CH/DVDUS, Canadian models: mode(8 ohms at 1 kHz, THD (Reference)0.8%) Front: 80 W/ch Center: (Pro Logic mode) 80 W Rear: 80 W/ch AEP model: (DIN 1 kHz, 4 ohms) Front: 70 W/ch Center: 70 W (only in PRO LOGIC mode) Rear: 70 W/ch E, Malaysia, Singapore, Chinese, Australian models: Rated power: (8 ohms at 1 kHz, THD 0.7 %) Front: 80 W/ch Center: (Pro Logic mode) 80 W Rear: 80 W/ch Continued on next page STR-SE391 (8 ohms at 1 kHz, THD 0.5 %) Front: 80 W/ch Center: (Pro Logic mode) 80 W Rear: 80 W/ch Reference power: (8 ohms 20 Hz 20 kHz, less than 0.09 % total harmonic distortion) Front: 70 W/ch Center: (Pro Logic mode) 70 W Rear: 70 W/ch RMS power: (8 ohms at 1 kHz, THD 10 %) Front: 100 W/ch Center: (Pro Logic mode) 100 W Rear: 100 W/ch FrequencyPHONO: RIAA responseequalization curve 0.5 dB (STR-SE391) TV/SAT (TV/LD), CD, MD/TAPE, VIDEO 5.1 CH/DVD: 10 Hz 50 kHz 1 dB RadioFans.CN 收音机爱 好者资料库 2 Inputs SensitivityImpedanceS/N PHONO (STR-4 mV 50 70 dB SE391) kilohms CD, 5.1 CH/150 mV DVD,(AEP model) 50 MD/TAPE,250 mV kilohms 80 dB TV/SAT,(EXCEPT (TV/LD)AEP models) VIDEO OutputsMD/TAPE REC OUT: Voltage: 150 mV, (US, AEP models) Voltage: 250 mV, (Canadian, E, Malaysia, Singapore, Australian and Chinese models) Impedance: 10 kilohms VIDEO AUDIO OUT: Voltage: 150 mV, (US, AEP models) Voltage: 250 mV, (Canadian, E, Malaysia Singapore, Australian and Chinese models) Impedance: 10 kilohms WOOFER: Voltage: 2V Impedance: 1 kilohms PHONES: Accepts low and high impedance headphones MutingFull mute BASS BOOST+ 10 dB at 70 Hz TONE 8 dB at 100 Hz and 10 kHz Tuner Section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range87.5 108.0 MHz Antenna terminals 75 ohms, unbalanced Intermediate10.7 MHz frequency SensitivityMono: 18.3 dBf, 2.2 V/75 ohms Stereo: 38.3 dBf, 22.5 V/75 ohms (AEP model) Mono: 18.3 dBf, 4.5 V Stereo: 38.3 dBf, 45 V (EXCEPT AEP models) Usable sensitivity11.2 dBf, 2 V (IHF) (US model) 11.2 dBf, 1 V/75 ohms (IHF) (AEP model) 11.2 dBf, 1 V (IHF) (EXCEPT US, AEP models) S/NMono: 76 dB Stereo: 70 dB HarmonicMono: 0.3 % distortion atStereo: 0.5 % 1 kHz Separation45 dB at 1kHz Frequency30 Hz 15 kHz dB response Selectivity60 dB at 400 kHz AM tuner section Tuning rangeAEP, Malaysia, Singapore, Australian and Chinese model: 531 1602 kHz (9 kHz step) US model: 530 1710 kHz (10kHz step)* 531 1710 kHz (9 kHz step) Canadian, E models: 530 1610 kHz (10kHz step)* 531 1602 kHz (9 kHz step) AntennaLoop antenna Intermediate450 kHz frequency Usable sensitivity50 dB/m (at 1,000kHz or 999 kHz) (US model) 50 dB/m (at 999 kHz) (EXCEPT US models) S/N54 dB (at 50 mV/m) Harmonic0.5 % (50 mV/m, 400Hz) distortion SelectivityAt 9 kHz: 35 dB At 10 kHz: 40 dB * You can change the AM tuning interval be- tween 9 kHz and 10 kHz. Turn off the re- ceiver and press 1/u (power) for more than 4 seconds until “INITIAL” appears. 1) After tuning in any AM station, turn off the receiver. 2) Hold down PRESET TUNING + button and press the 1/u (power) button. “9k STEP” appears. To change to 10k Step, repeat step 1 and 2 until “10k STEP” appears. Note that all preset stations, index names and sound field are cleared after you make the procedure above. Video section (STR-DE335/V323) InputsVIDEO, TV/SAT (TV/LD), 5.1 CH/DVD: 1 Vp-p 75 ohms OutputVIDEO, MONITOR: 1 Vp-p 75 ohms General SystemTuner section: PLL quartz-locked digital synthesizer system Preamplifier section: Low-noise NF type equalizer Power amplifier section: Pure-complementary SEPP PowerUS, Canadian models: requirements120 V AC, 60 Hz Australian model: 240 V AC, 50 Hz AEP, Malaysia, Singapore and Chinese models: 230 V AC, 50/60 Hz E model 120/220/240 V AC, 50/60 Hz PowerUS model: 230 W consumptionCanadian model: 325 VA AEP model: 225 W Malaysia, Singapore and Australian and Chinese models: 235 W E model 245 W +0.5 2 AC outletsSTR-DE335 US, Canadian models: 1 switched, 120 W/1A max STR-DE335 AEP, E, Malaysia, Singapore, Australian models: STR-V323 1 switched, 100 W max STR-SE391 2 switched, total 120 W/1A max Dimensions430 144 306 mm Mass (Approx.)STR-DE335: US model 8.7 kg STR-DE335: AEP model 7.7 kg EXCEPT DE335: US, AEP models 8.8 kg SuppliedFM wire antenna (1) accessoriesAM loop antenna (1) Remote commander (remote) (1) Size AA (R6) batteries (2) The specification measured is under 230 AC, 50Hz condition (AEP, Malaysia, Singapore and Chinese models) 240 AC, 50Hz condition (Australian model) Design and specifications are subject to change without notice. RadioFans.CN 收音机爱 好者资料库 3 SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. TABLE OF CONTENTS 1.SERVICING NOTES.4 2.GENERAL.5 3.DISASSEMBLY.7 4.TEST MODE.9 5.DIAGRAMS 5-1.Block Diagram MAIN Section (1/2) . 11 5-2.Block Diagram MAIN Section (2/2) . 13 5-3.Block Diagram DISPLAY/ POWER SUPPLY Section . 15 5-4.Note for Printed Wiring Boards and Schematic Diagrams . 17 5-5.Printed Wiring Board MAIN Board . 21 5-6.Printed Wiring Boards REAR AMP Board/ SP SW Board/SECONDARY Board/ STANDBY Board/PRIMARY Board/ VOL SEL Board . 23 5-7.Schematic Diagram MAIN Board (1/4)/ REAR AMP Board . 25 5-8.Schematic Diagram MAIN Board (2/4)/ SP SW Board . 27 5-9.Schematic Diagram MAIN Board (3/4) . 29 5-10. Schematic Diagram MAIN Board (4/4)/ SECONDARY Board /STANDBY board/ PRIMARY Baord/VOL SEL Board . 31 5-11. Printed Wiring Board PANEL Section . 33 5-12. Schematic Diagram PANEL Section . 35 5-13. Printed Wiring Boards VOLUME Board/ TONE Board/VIDEO Board/PHONO Board . 37 5-14. Schematic Diagram VOLUME Board/ TONE Board/VIDEO Board/PHONO Board . 39 5-15. IC Pin Function Description . 44 6.EXPLODED VIEWS. 46 7.ELECTRICAL PARTS LIST. 50 ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. 4 SECTION 1 SERVICING NOTES MODEL IDENTIFICATION Rear view 1234 PART No. MODELPART No. DE 335:US model4-218-844-0 DE 335: Canadian model4-218-844-1 DE 335: Australian model4-218-844-2 DE 335: Malaysia, Singapore models4-218-844-3 V 3234-218-844-4 DE 335: E model4-218-844-5 DE 335: AEP model4-218-844-6 SE 3914-218-844-7 SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica- tion is 0.75 V, so analog meters must have an accurate low- voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex- amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit- able. (See Fig. A) Fig. A.Using an AC voltmeter to check AC leakage. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground 5 SECTION 2 GENERAL 1 I/u button 2 TUNING +, buttons 3 DISPLAY button 4 PRESET/TUNING +, buttons (EXCEPT AEP model) PRESET/PTY SELECT +, buttons (AEP model) 5 RDS PTY button(AEP model) 6 AM button(EXCEPT AEP models) RDS EON button(AEP model) 7 FM button(EXCEPT AEP models) FM/AM button(AEP model) 8 VIDEO button 9 TV/SAT button (US, Canadian, Australian models) TV/LD button (AEP, E, Malaysia, Singapore, Chinese models) Location of controls Front view 0 MD/TAPE button ! 5.1 CH/DVD button and indicator ! SOUND FIELD + MODE, ON/OFF, MODE buttons ! SET UP button and indicator ! CINEMA indicator ! VIRTUAL indicator ! MUSIC indicator ! BASS BOOST button and indicator ! SPEAKERS A, B ON/OFF buttons ! PHONES jack SHIFT button Numeric buttons DIRECT button MEMORY button FM MODE button CD button TUNER button PHONO button (SE391) EFFECT/DELAY button and indicator CENTER button and indicator # button # + button # REAR button and indicator # ENTER button # NAME button and indicator # VOLUME control # MUTING button and indicator # TREBLE control # BASS control # BALANCE control 34 51267!890! ! ! ! ! # # # # # # # 6 Rear View STR-DE335/V323 1 ANTENNA (AM/FM) 2 CD 3 MD/TAPE 4 5.1 CH/DVD 5 TV/SAT (US, Canadian, Australian models) TV/LD (AEP, E, Malaysia, Singapore, Chinese models) 6 VIDEO 7 MONITOR 8 WOOFER 9 SWITCHED AC OUTLET (Malaysia, Sigapore, Australian, Chinese models) 0 VOLTAGE SELECTOR (E model) ! AC power cord ! SWITCHED AC OUTLET (US, Canadian, E, Chinese models) ! SPEAKERS FRONT (A/B) ! SPEAKERS CENTER ! SPEAKERS REAR 1 ANTENNA (AM/FM) 2 PHONO 3 5.1 CH/DVD 4 y ground terminal 5 CD 6 MD/TAPE 7 TV/SAT 8 VIDEO 9 WOOFER 0 AC power cord ! SWITCHED AC OUTLET ! SPEAKERS FRONT (A/B) ! SPEAKERS CENTER ! SPEAKERS REAR STR-SE391 7 CASE FRONT PANEL SECTION Note: Follow the disassembly procedure in the numerical order given. SECTION 3 DISASSEMBLY 1two screws (case 3 TP2) 1screw (case 3 TP2) 2case 1two screws (case 3 TP2) 2three connectors (CNP702 704) 3screw (BVTP3 8) 4claw 5front panel section 3four screws (BVTP3 8) 4claw 1three flat wires (CNS204, 403, 701) 1flat wire (CNS503) 8 REAR PANEL SECTION MAIN BOARD SECTION 2connector (CNP901) 4rear panel section 3two screws (BVTP3 8) 3seven screws (BVTP3 8) 1flat wire (CNS401) 1flat wire (CNS205) 3four screws (BVTP3 8) 2connector (CNP500) 2connector (CNS802) 2two connectors (CNP703, 704) 4PC board holder 2connector (CNP801) 1three flat wires (CNS204, CNP404) 5MAIN board section 3three screws (BVTP3 8) 3three screws (BVTP3 8) 2connector (CNP702) 1flat wire (CNS503) 9 SECTION 4 TEST MODE Initialization Mode All preset contents are cleared when this mode is activated. When returning the unit to the customer after completing repairs, per- form this operation to clear the unit. Procedure: 1.While pressing two buttons of TUNER and MD/TAPE si- multaneously, press the 1/u button to turn the power ON. 2.The message “INITIAL” appears and initialization is per- formed. Fluorescent Indicator Tube Test Mode All fluorescent segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another. Procedure: 1.While pressing two buttons of TV/SAT (US , Canadian and Australian models)* and DIRECT simultaneously, press the 1/u button to turn the power ON. 2.All segments turn on at the same time, then each segment and LED turns on one after another. 3.The message “FINISH” appears when this test is complete. *) Except US, Canadian and Australian models are TV/LD AUTO-BETICAL Check Mode (AEP model) To auto-scanning and memories of RDS station. Procedure: 1.While pressing the MEMORY button, press the 1/u button to turn the power ON. 2.The message “AUTO BET” appears and each function is se- lected one after another. AM Tuning Interval Selection Mode (US, Canadian and E models) Either 9 kHz step or 10 kHz step can be selected for the AM tun- ing interval. Procedure: 1.Set the FUNCTION to AM. 2.Press the 1/u button to turn the power OFF. 3.While pressing the TUNING+ or PRESET+button, press the 1/u button to turn the power ON. 4.Either the message 10 k STEP” or “10k STEP” appears. 5.Select the desired step. Software Version Display Mode The software version is displayed. Procedure: 1.While pressing two the buttons of MD/TAPE and DIRECT simultaneously, press the 1/u button to turn the power ON. 2.The software version is displayed. SOUND FIELD Setting Clear Mode All SOUND FIELD setting are cleared. Procedure: 1.While pressing the SOUNDFIELDON/OFF button, press the 1/u button to turn the power ON. 2.The message “SURR CLR” appears and all SOUND FIELD setting are cleared. STR-DE335/SE391/V323 11 12 SECTION 5 DIAGRAMS 5-1.BLOCK DIAGRAM MAIN Section (1/2) VIDEO SELECT SWITCH, VIDEO AMP IC251 FUNCTION SWITCH IC401 DOLBY SURROUND PRO-LOGIC DECODER IC300 DOLBY SURROUND PASSIVE DECODER IC301 VOLUME MOTOR DRIVE IC202 SYSTEM CONTROLLER IC201 (1/2) 05 D (Page 11) E (Page 11) (Page 11) C (Page 11) B (Page 11) A (Page 11) SIGNAL PATH : TUNER (FM) : VIDEO FM/AM TUNER PACK COM COM L OUTFM-ANT FM-ANT GND AM-ANT AM-ANT