Sony-STRK6800P-rec-sm维修电路原理图.pdf

1 SERVICE MANUALUS Model STR-K6800P AEP Model UK Model Australian Model STR-DE597P STR-DE597P/K6800P FM STEREO/FM-AM RECEIVER AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code US only) With 8 ohm loads, both channels driven, from 120 20,000 Hz; rated 90 watts per channel minimum RMS power, with no more than 0.7 % total harmonic distortion from 250 milliwatts to rated output. Amplifier section Power Output 1) Models of area code US (8 ohms 1 kHz, THD 10 %) FRONT 2) : 120 W/ch CENTER 2) : 120 W SURR 2) : 120 W/ch SURR BACK 2) : 120 W Models of area code AEP, UK (8 ohms 1 kHz, THD 0.7 %) FRONT 2) : 100 W/ch CENTER 2) : 100 W SURR 2) : 100 W/ch SURR BACK 2) : 100 W (8 ohms 1 kHz, THD 10 %) FRONT 2) : 120 W/ch CENTER 2) : 120 W SURR 2) : 120 W/ch SURR BACK 2) : 120 W SPECIFICATIONS Models of area code AUS (8 ohms 120 Hz 20 kHz, THD 0.09 %) FRONT 2) : 80 W/ch CENTER 2) : 80 W SURR 2) : 80 W/ch SURR BACK 2) : 80 W (8 ohms 1 kHz, THD 0.7 %) FRONT 2) : 100 W/ch CENTER 2) : 100 W SURR 2) : 100 W/ch SURR BACK 2) : 100 W (8 ohms 1 kHz, THD 10 %) FRONT 2) : 120 W/ch CENTER 2) : 120 W SURR 2) : 120 W/ch SURR BACK 2) : 120 W 1) Measured under the following conditions: Area codePower requirements US120 V AC, 60 Hz AEP, UK230 V AC, 50 Hz AUS240 V AC, 50 Hz 2) Depending on the sound field settings and the source, there may be no sound output. Ver 1.0 2004. 06 9-879-028-01 2004F04-1 2004. 06 Sony Corporation Home Audio Company Published by Sony Engineering Corporation Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. “DTS”, “DTS-ES”, “Neo:6” are trademarks of Digital Theater Systems, Inc. Continued on next page Photo: STR-K6800P STR-DE597P/K6800P are the FM/AM receiver section in HT-DDW860/6800DP. RadioFans.CN 收音机爱 好者资料库 2 STR-DE597P/K6800P Inputs (Analog) MULTI CH IN, SA-CD/Sensitivity: 800 mV CD, MD/TAPE, DVD,Impedance: 50 kiloohms VIDEO 1, 2 Inputs (Digital) DVD (Coaxial)Sensitivity: Impedance: 75 ohms VIDEO 2, SA-CD/CDSensitivity: (Optical)Impedance: Outputs (Analog) MD/TAPE (OUT),Voltage: 800 mV VIDEO 1 (AUDIO OUT)Impedance: 10 kiloohms SUB WOOFERVoltage: 2 V Impedance: 1 kiloohms Reproduction frequency range: 28 20,000 Hz Tone Gain levels6 dB, 1 dB step FM tuner section Tuning range87.5 108.0 MHz AntennaFM wire antenna Antenna terminals75 ohms, unbalanced Intermediate frequency10.7 MHz AM tuner section Tuning range Models of area code US With 10-kHz tuning scale: 530 1,710 kHz 3) With 9-kHz tuning scale:531 1,710 kHz 3) Models of area code AEP, UK, AUS With 9-kHz tuning scale:531 1,602 kHz AntennaLoop antenna Intermediate frequency450 kHz 3) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down PRESET TUNING + or TUNING +, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure. Video section Inputs/Outputs Video:1 Vp-p, 75 ohms COMPONENT VIDEO: (Except for models of area code AEP, UK) Y: 1 Vp-p, 75 ohms PB/CB/B-Y: 0.7 Vp-p, 75 ohms PR/CR/R-Y: 0.7 Vp-p, 75 ohms 80 MHz HD Pass Through General Power requirements Area codePower requirements US120 V AC, 60 Hz AEP, UK230 V AC, 50/60 Hz AUS240 V AC, 50 Hz Power consumption220 W Power consumption (during standby mode) 0.3 W Dimensions (w/h/d) (Approx.) 430 157.5 312 mm (16 7/8 6 2/8 12 2/8 inches) including projecting parts and controls Mass (Approx.)8.0 kg (17 lb 11 oz) Design and specifications are subject to change without notice. Abbreviation AUS : Australian model RadioFans.CN 收音机爱 好者资料库 3 MODEL IDENTIFICATION BACK PANEL Part No. MODELPART No. STR-K6800P: US4-254-238-0s STR-DE597P: AEP4-254-238-1s STR-DE597P: UK4-254-238-2s STR-DE597P: AUS4-254-238-3s Abbreviation AUS : Australian model STR-DE597P/K6800P SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica- tion is 0.75 V, so analog meters must have an accurate low- voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex- amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit- able. (See Fig. A) Fig. A. Using an AC voltmeter to check AC leakage. 4 STR-DE597P/K6800P TABLE OF CONTENTS 1. GENERAL Main unit . 5 Remote button description. 6 2. DISASSEMBLY 2-1. Case . 7 2-2. Front Panel Section . 8 2-3. Back Panel Section. 8 2-4. Digital Board. 9 2-5. Standby Board . 9 2-6. Main Board .10 2-7. SB AMP Board. 10 3. TEST MODE. 11 4. DIAGRAMS 4-1. Circuit Boards Location . 12 4-2. Block Diagram Tuner/Audio Section . 13 4-3. Block Diagram Digital Section .14 4-4. Block Diagram Video Section . 15 4-5. Block Diagram Key/Display Section . 16 4-6. Block Diagram Power Section . 17 4-7. Printed Wiring Boards Main Section . 19 4-8. Schematic Diagram Main Section (1/2) . 20 4-9. Schematic Diagram Main Section (2/2) . 21 4-10. Printed Wiring Board Digital Section (1/2) . 22 4-11. Printed Wiring Board Digital Section (2/2) . 23 4-12. Schematic Diagram Digital Section (1/3) .24 4-13. Schematic Diagram Digital Section (2/3) .25 4-14. Schematic Diagram Digital Section (3/3) .26 4-15. Printed Wiring Boards Center/Surround Back Speaker Section . 27 4-16. Schematic Diagram Center/Surround Back Speaker Section . 28 4-17. Printed Wiring Board Video Section .29 4-18. Schematic Diagram Video Section . 30 4-19. Printed Wiring Boards Display Section . 31 4-20. Schematic Diagram Display Section .32 4-21. Printed Wiring Boards Power Section . 33 4-22. Schematic Diagram Power Section . 34 4-23. IC Block Diagrams. 35 5. EXPLODED VIEWS 5-1. Case Section . 42 5-2. Front Panel Section .43 5-3. Back Panel Section. 44 5-4. Chassis Section . 45 6. ELECTRICAL PARTS LIST. 46 5 STR-DE597P/K6800P SECTION 1 GENERALThis section is extracted from instruction manual. 6 STR-DE597P/K6800P 7 STR-DE597P/K6800P Note : This set can be disassemble according to the following sequence. SECTION 2 DISASSEMBLY 2-1. CASE 2-1.CASE (Page 7) 2-2.FRONT PANEL SECTION (Page 8) 2-3.BACK PANEL SECTION (Page 8) SET 2-5.STANDBY BOARD (Page 9) 2-7.SB AMP BOARD (Page 10) 2-4.DIGITAL BOARD (Page 9) 2-6.MAIN BOARD (Page 10) Note : Follow the disassembly procedure in the numerical order given. 1 two screws (case 3 TP2) 2 two screws (case 3 TP2) 3 two screws (case 3 TP2) 4 case 8 STR-DE597P/K6800P 2-2. FRONT PANEL SECTION 2-3. BACK PANEL SECTION 6 front panel section 1 CNS505 2 CNP791 5 three screws (+BVTP 3 x 8) 3 two screws (+BVTP 3 x 8) 4 two screws (+BVTP 3 x 8) 1 CNS250 3 CNP203 2 connector 6 CNP501 5 CNP502 0 CNP901 9 CN908 8 CN906 7 CNP913 4 CNP503 qs screws (+BVTP 3 x 8) qg seven screws (+BVTP 3 x 8) qf two screws (+BVTP 3 x 8) qj back panel section qh three screws (+BVTP 3 x 8) qa three screws (+BVTP 3 x 8) qd screw (+BVTP 3 x 8) 9 STR-DE597P/K6800P 2-4. DIGITAL BOARD 7 CNP501 5 6 CNP500 1 CNP506 2 CNP510 3 CNP507 9 bracket (digital) 0 DIGITAL board 4 screw (+BVTP 3 x 8) 8 screw (+BVTP 3 x 8) 6 STANDBY board 1 CNP915 4 CNP903 2 CNP804 3 CNP902 5 three screws (+BV SUMITITE (B3) 2-5. STANDBY BOARD 10 STR-DE597P/K6800P 6 screw (+BV SUMITITE (B3) 4 two screws (+BV SUMITITE (B3) 5 two screws (+BV SUMITITE (B3) 7 two screws (+BV SUMITITE (B3) 8 MAIN board 1 CNP915 2 CNP912 3 CNP802 2-6. MAIN BOARD 2-7. SB AMP BOARD 3 three screws (transistor) 7 SB AMP board 1 CN572 2 CN574 5 bracket (SUR) 6 bracket (SUR) 4 two screws (+BVTP 3 x 8) 11 STR-DE597P/K6800P SECTION 3 TEST MODE FACTORY PRESET MODE * All preset contents are reset to the default setting. * Procedure: While depressing the FM MODE and the DISPLAY buttons simultaneously, press the ?/1 button to turn on the main power. The message “FACTORY” appears for a moment and the present contents are reset to the default values. AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE (US model only) * Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. * Procedure: Press the TUNER FM/AM button to set AM and press the ?/1 button to turn off the main power. While depressing the PRESET TUNING + button or the TUNING + button, press the ?/1 button to turn on the main power. Either the message “9k STEP” or “10k STEP” appears for a moment and select the desired step. SPEAKER SIZE SELECTION MODE * Either the normal speaker or micro satellite speaker can be se- lected. * Procedure: While depressing the DIMMER button, press the ?/1 button to turn on the main power. Either the message “NORM. SP.” or “MICRO SP.” appears for a moment and select the desired speaker size. VACUUM FLUORESCENT DISPLAY TEST MODE * All fluorescent segments are tested. When this test is activated, all segments light on at the same time, then each segment lights on one after another. * Procedure: While depressing the TUNING - and the SPEAKERS $OFF/A/ B/A+B% buttons simultaneously, press the ?/1 button to turn on the main power. 1.ALL segments light on. 2CH, A.F.D., MOVIE, MUSIC and MULTI CHANNEL DE- CODING LED light on. 2.Press the VIDEO 1 button, confirm display. A.F.D. and MUSIC LED light on. 3.Press the VIDEO 1 button, confirm display. 2CH, MOVIE and MULTI CHANNEL DECODING LED light on. 4.Press the VIDEO 1 button, all segments and all LEDs light off. 5.Every pressing the VIDEO 1 button turns on each segment and LED one after another in the same order. (Not only the VIDEO 1 button, but also the other buttons such as VIDEO 2, DVD, MD/TAPE, SA-CD/CD and TUNER FM/ AM can be used.) SOUND FIELD CLEAR MODE * The preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. * Procedure: While depressing the 2CH button, press the ?/1 button to turn on the main power. The message “SF. CLR.” appears for a moment and initializa- tion is performed. SOFTWARE VERSION DISPLAY MODE * The software version is displayed. * Procedure: While depressing the TUNING - and the DISPLAY buttons simultaneously, press the ?/1 button to turn on the main power. The model name, destination and the software version are dis- played for a moment. KEY CHECK MODE * Button check * Procedure: While depressing the TUNING - and the MAIN MENU buttons simultaneously, press the ?/1 button to turn on the main power. Either the message “REST 28” appears. Every pressing of any button other than the ?/1 counts down the buttons. The buttons which are already counted once are not counted again. When all buttons are pressed “REST 00” appears. AUTOBETICAL MODE (AEP, UK model only) * When this mode is used, the receiver scans the broadcasts that can be received by the tuner, and sets up the broadcasts. Be sure to start scanning after connecting the antenna. * Procedure: Check that the antenna is connected. While depressing the MEMORY button, press the ?/1 button to turn on the main power. The message “AUTO-BETICAL SELECT” appears for a mo- ment and the receiver starts scanning. COMMAND MODE SELECTION MODE * The command mode (AV1 or AV2) of the remote commander can be selected. * Procedure: While depressing the ENTER button, press the ?/1 button to turn on the main power. Either the message “C.MODE.AV 1” or “C.MODE.AV 2” ap- pears for a moment and select the desired mode. L SW CR SLSSR SBLSBSBR LFESP A SP B SLEEP OPT COAX MULTI CH IN 96/24 DIGITALEXPRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDS D.RANGE EQ STEREO MONO DDDD dB kHz mft. MHz MEMORY DIRECT L SW R S SB LFESP A SP B SLEEP OPT COAX MULTI CH IN 96/24 DIGITALEXPRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDS D.RANGE EQ STEREO MONO DDDD dB kHz mft. MHz MEMORY DIRECT C SLSR SBLSBR SP A SP B SLEEP OPT COAX MULTI CH IN 96/24 DIGITALEXPRO LOGIC II x DTS-ES NEO:6 MPEG-2 AAC RDS D.RANGE EQ STEREO MONO DDDD kHz mft. MHz MEMORY DIRECT 12 STR-DE597P/K6800P SECTION 4 DIAGRAMS 4-1. CIRCUIT BOARDS LOCATION DIGITAL board POWER board STANDBY board BRIDGEABLE board VIDEO board SB AMP board SPEAKER board MAIN board TUNING board HEADPHONE board DISPLAY board STR-DE597P/K6800P 1313 STR-DE597P/K6800P 4-2. BLOCK DIAGRAM TUNER/AUDIO SECTION 43 76 75 78 74 73 70 SA-CD/CD IN MD/TAPE OUT MD/TAPE IN