Sony-STRDE595-int-sm维修电路原理图.pdf

1 SERVICE MANUALUS Model Canadian Model STR-DE595 AEP Model UK Model E Model Australian Model Korean Model STR-DE495/DE595 STR-DE495/DE595 FM STEREO/FM-AM RECEIVER AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 ohm loads, both channels driven, from 40 20,000 Hz; rated 90 watts per channel minimum RMS power, with no more than 0.09 % total harmonic distortion from 250 milliwatts to rated output (STR-DE595 area code US only). Amplifier section POWER OUTPUT Models of area code US, CND Rated Power Output at Stereo Mode (8 ohms 40 Hz 20 kHz, THD 0.09 %) STR-DE595:90 W + 90 W STR-DE495:70 W + 70 W Reference Power Output (8 ohms 40 Hz 20 kHz, THD 0.09 %) STR-DE595:FRONT 1) : 90 W/ch CENTER 1) : 90 W SURR 1) : 90 W/ch STR-DE495:FRONT 1) : 70 W/ch CENTER 1) : 70 W SURR 1) : 70 W/ch (8 ohms 1 kHz, THD 0.7 %) STR-DE595:FRONT 1) : 100 W/ch CENTER 1) : 100 W SURR 1) : 100 W/ch STR-DE495:FRONT 1) : 80 W/ch CENTER 1) : 80 W SURR 1) : 80 W/ch SPECIFICATIONS Models of area code AEP, UK Rated Power Output at Stereo Mode (8 ohms 1 kHz, THD 0.7 %) STR-DE595:100 W + 100 W 2) STR-DE495:80 W + 80 W 2) Reference Power Output 2) (8 ohms 1 kHz, THD 0.7 %) STR-DE595:FRONT 1) : 100 W/ch CENTER 1) : 100 W SURR 1) : 100 W/ch STR-DE495:FRONT 1) : 80 W/ch CENTER 1) : 80 W SURR 1) : 80 W/ch Models of area code SP Rated Power Output at Stereo Mode (8 ohms 1 kHz, THD 0.7 %) STR-DE595:90 W + 90 W 2) STR-DE495:70 W + 70 W 2) Reference Power Output 2) (8 ohms 1 kHz, THD 10 %) STR-DE595:FRONT 1) : 110 W/ch CENTER 1) : 110 W SURR 1) : 110 W/ch STR-DE495:FRONT 1) : 90 W/ch CENTER 1) : 90 W SURR 1) : 90 W/ch Ver 1.1 2003. 04 9-877-028-02 2003D0400-1 2003. 04 Sony Corporation Home Audio Company Published by Sony Engineering Corporation Photo: STR-DE595 Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc. Continued on next page Models of area code KR Rated Power Output at Stereo Mode (8 ohms 1 kHz, THD 0.7 %) STR-DE595:100 W + 100 W 2) 90 W + 90 W 3) STR-DE495:80 W + 80 W 2) 70 W + 70 W 3) Reference Power Output 2) (8 ohms 1 kHz, THD 10 %) STR-DE595:FRONT 1) : 120 W/ch CENTER 1) : 120 W SURR 1) : 120 W/ch STR-DE495:FRONT 1) : 100 W/ch CENTER 1) : 100 W SURR 1) : 100 W/ch Models of other area code Rated Power Output at Stereo Mode (8 ohms 1 kHz, THD 0.7 %) STR-DE595:100 W + 100 W 2) STR-DE495:80 W + 80 W 2) Reference Power Output 2) (8 ohms 1 kHz, THD 10 %) STR-DE595:FRONT 1) : 120 W/ch CENTER 1) : 120 W SURR 1) : 120 W/ch STR-DE495:FRONT 1) : 100 W/ch CENTER 1) : 100 W SURR 1) : 100 W/ch RadioFans.CN 收音机爱 好者资料库 2 STR-DE495/DE595 1) Depending on the sound field settings and the source, there may be no sound output. 2) Measured under the following conditions: Area codePower requirements E2, AUS240 V AC, 50 Hz SP, MY, AEP, UK, AR,230 V AC, 50 Hz KR TW110 V AC, 60 Hz Frequency response MULTI CH IN10 Hz 50 kHz (STR-DE595 only), CD+0.5/2 dB (with sound (STR-DE495 only),field and tone bypassed) MD/TAPE, DVD, VIDEO 1, 2 CD/SACD (STR-DE59510 Hz 70 kHz only)+0.5/2 dB (with sound field and tone bypassed) Inputs (Analog) MULTI CH INSensitivity: 500 mV (STR-DE595 only), CD/Impedance: 50 kilohms SACD (STR-DE595S/N 3) : 96 dB only), CD (STR-DE495(A, 500 mV 4) ) only), MD/TAPE, DVD, VIDEO 1, 2 3) INPUT SHORT (with sound field and tone bypassed). 4) Weighted network, input level. Inputs (Digital) DVD (Coaxial)Sensitivity: Impedance: 75 ohms S/N: 100 dB (A, 20 kHz LPF) CD/SACD (Optical)Sensitivity: (STR-DE595 only),Impedance: VIDEO 2 (Optical)S/N: 100 dB (A, 20 kHz LPF) Outputs MD/TAPE (OUT),Voltage: 500 mV VIDEO1Impedance: 10 kilohms (AUDIO OUT) SUB WOOFERVoltage: 2 V Impedance: 1 kilohms Tone Gain levels:6 dB, 1 dB step FM tuner section Tuning range87.5 - 108.0 MHz Antenna terminals75 ohms, unbalanced Intermediate Frequency10.7 MHz Sensitivity Mono:18.3 dBf, 2.2 V/75 ohms Stereo:38.3 dBf, 22.5 V/75 ohms Usable sensitivity11.2 dBf, 1 V/75 ohms S/N Mono:76 dB Stereo:70 dB Harmonic distortion at 1 kHz Mono:0.3% Stereo:0.5% Separation45 dB at 1 kHz Frequency response30 Hz 15 kHz, +0.5/2 dB Selectivity60 dB at 400 kHz AM tuner section Tuning range Models of area code US, CND With 10-kHz tuning scale: 530 1710 kHz 5) With 9-kHz tuning scale:531 1710 kHz 5) Models of area code E2 With 10-kHz tuning scale: 530 1610 kHz 5) With 9-kHz tuning scale:531 1602 kHz 5) Models of area code AUS, SP, AEP, UK, TW, KR With 9-kHz tuning scale:531 1602 kHz Models of area code MX, AR With 10-kHz tuning scale: 530 1610 kHz AntennaLoop antenna Intermediate Frequency450 kHz Usable sensitivity50 dB/m (at 1,000 kHz or 999 kHz) S/N54 dB (at 50 mV/m) Harmonic distortion0.5 % (50 mV/m, 400 Hz) Selectivity At 9 kHz:35 dB At 10 kHz:40 dB 5) You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. Hold down PRESET TUNING + and press ?/1 . All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure. Video section Inputs Video:1 Vp-p, 75 ohms Component Video (STR-DE595 only, except for models of area code AEP, UK): Y:1 Vp-p, 75 ohms PB/B-Y:0.7 Vp-p, 75 ohms PR/R-Y:0.7 Vp-p, 75 ohms Outputs Video:1 Vp-p, 75 ohms Component Video (STR-DE595 only, except for models of area code AEP, UK): Y:1 Vp-p, 75 ohms PB/B-Y:0.7 Vp-p, 75 ohms PR/R-Y:0.7 Vp-p, 75 ohms General Power requirements Area codePower requirements US, CND, MX120 V AC, 60 Hz AEP, UK230 V AC, 50/60 Hz SP, MY, KR, AR220 230 V AC, 50/60 Hz E2120/220/240 V AC, 50/60 Hz TW110 V AC, 50/60 Hz AUS240 V AC, 50Hz Power consumption Area codePower consumption US, MXSTR-DE595: 210 W CNDSTR-DE595: 310 VA AEP, UK, TW, KRSTR-DE595: 210 W STR-DE495: 180 W SP, MYSTR-DE595: 180 W AUS, E2, ARSTR-DE595: 210 W Power consumption (during standby mode) 0.3 W Dimensions430 145 298 mm (16 7/8 5 6/8 11 6/8 in.) including projecting parts and controls Mass (Approx.)STR-DE595: 7.5 kg (16 lb 9 oz) STR-DE495: 7.2 kg (15 lb 14 oz) Supplied accessories FM wire antenna (1) AM loop antenna (1) Remote commander RM-U306A (1) R6 (size-AA) batteries (2) Design and specifications are subject to change without notice. Abbreviation CND: Canadian model AUS: Australian model MX: Mexican model SP: Singapore model E2: AC 120 V area in E model AR: Argentine model KR: Korean model TW: Taiwan model Ver 1.1 RadioFans.CN 收音机爱 好者资料库 3 STR-DE495/DE595 MODEL IDENTIFICATION BACK PANEL Part No. MODELPART No. DE595: Korean4-244-149-0s DE595: Taiwan4-244-149-1s DE595: Argentine4-244-149-4s DE595: US4-246-023-0s DE595: Canadian4-246-023-1s DE595: Australian4-246-023-2s DE595: Singapore, Malaysia4-246-023-3s DE595: E24-246-023-4s DE595: Mexican4-246-023-5s DE595: AEP4-246-023-6s DE595: UK4-246-023-7s DE495: AEP4-246-034-1s DE595: UK4-246-034-2s DE495: Singapore, Malaysia4-246-034-3s DE495: Taiwan4-246-034-4s DE495: Korean4-246-034-5s DE495: Australian4-246-034-7s 1.5 k0.15 F AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground SAFETY CHECK-OUT After correcting the original service problem, perform the follow- ing safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers.). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indica- tion is 0.75 V, so analog meters must have an accurate low- voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex- amples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suit- able. (See Fig. A) SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY. Ver 1.1 4 TABLE OF CONTENTS 1. GENERAL Main unit . 5 Remote button description. 6 2. DISASSEMBLY 2-1. Case . 7 2-2. Front Panel Section . 8 2-3. Back Panel. 8 2-4. Digital Board. 9 2-5. Standby Board . 9 2-6. Main Board .10 3. TEST MODE. 11 4. DIAGRAMS 4-1. IC Pin Descriptions .12 4-2. Circuit Boards Location . 15 4-3. Block Diagram Tuner/Audio Section . 16 4-4. Block Diagram Digital Section .17 4-5. Block Diagram Video/Display Section .18 4-6. Block Diagram Power Section . 19 4-7. Printed Wiring Boards Main Section . 21 4-8. Schematic Diagram Main Section (1/2) . 22 4-9. Schematic Diagram Main Section (2/2) . 23 4-10. Printed Wiring Board Digital Section (1/2) . 24 4-11. Printed Wiring Board Digital Section (2/2) . 25 4-12. Schematic Diagram Digital Section (1/2) .26 4-13. Schematic Diagram Digital Section (2/2) .27 4-14. Printed Wiring Board Video Section .28 4-15. Schematic Diagram Video Section . 29 4-16. Printed Wiring Boards Display Section . 30 4-17. Schematic Diagram Display Section .31 4-18. Printed Wiring Boards Power Section . 32 4-19. Schematic Diagram Power Section . 33 4-20. IC Block Diagrams. 34 5. EXPLODED VIEWS 5-1. Case Section . 36 5-2. Front Panel Section .37 5-3. Chassis Section-1 . 38 5-4. Chassis Section-2 . 39 6. ELECTRICAL PARTS LIST. 40 STR-DE495/DE595 5 STR-DE495/DE595 SECTION 1 GENERALThis section is extracted from instruction manual. 6 STR-DE495/DE595 7 STR-DE495/DE595 Note : This set can be disassemble according to the following sequence. SECTION 2 DISASSEMBLY 2-1. CASE 2-1.CASE (Page 7) 2-2.FRONT PANEL SECTION (Page 8) 2-3.BACK PANEL (Page 8) SET 2-5.STANDBY BOARD (Page 9) 2-4.DIGITAL BOARD (Page 9) 2-6.MAIN BOARD (Page 10) Note : Follow the disassembly procedure in the numerical order given. 1 two screws (case 3 TP2) 2 three screws (case 3 TP2) 3 two screws (case 3 TP2) 4 case 8 STR-DE495/DE595 2-2. FRONT PANEL SECTION 2-3. BACK PANEL 5 front panel section 3 two screws (BVTP3 x 8) 1 CNS4 2 CNP791 4 five screws (BVTP3 x 8) 1 CNS7 2 CNS8 4 CNP901 5 CN908 6 CN906 3 CNP156 7 three screws (BVTP3 x 8) 9 three screws (BVTP3 x 8) 9 six screws (BVTP3 x 8) 8 five screws (BVTP3 x 8) qa screw (BVTP3 x 8) 0 screw (BVTP3 x 8) qs back panel 9 STR-DE495/DE595 2-4. DIGITAL BOARD 1 CNS4 5 CNS1 6 CNS2 2 CNP6 3 CNP5 8 screw (BVTP3 x 8) 9 bracket (digital) 7 DIGITAL board 4 screw (BVTP3 x 8) 5 STANDBY board 1 CNP905 2 CNP902 3 CNP903 4 three screws (BVTP3 x 6) 2-5. STANDBY BOARD Ver 1.1 10 STR-DE495/DE595 7 MAIN board 1 CNP801 2 CNP802 5 screw (BVTP3 x 6) 3 two screws (BVTP3 x 6) 4 two screws (BVTP3 x 6) 6 two screws (BVTP3 x 6) 2-6. MAIN BOARD Ver 1.1 11 STR-DE495/DE595 SECTION 3 TEST MODE FACTORY PRESET MODE * All preset contents are reset to the default setting. * Procedure: While depressing the FM MODE and the PRESET TUNING - buttons simultaneously, press the ?/1 button to turn on the main power. The message “FACTORY” appears for a moment and the present contents are reset to the default values. AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE (US, Canadian, E model only) * Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. * Procedure: Press the TUNER FM/AM button to set AM and press the ?/1 button to turn off the main power. While depressing the TUNING + button or the PRESET TUNING + button, press the ?/1 button to turn on the main power. Either the message “9k STEP” or “10k STEP” appears for a moment and select the desired step. SPEAKER SIZE SELECTION MODE * Either the normal speaker or micro satellite speaker can be se- lected. * Procedure: While depressing the MAIN MENU button, press the ?/1 but- ton to turn on the main power. Either the message “NORM. SP.” or “MICRO SP.” appears for a moment and select the desired speaker size. FLUORESCENT INDICATOR TUBE TEST MODE * All fluorescent segments are tested. When this test is activated, all segments light on at the same time, then each segment lights on one after another. * Procedure: While depressing the FM MODE and the MD/TAPE buttons simultaneously, press the ?/1 button to turn on the main power. 1.ALL segments light on. 2CH, SURROUND, MOVIE and MUSIC LED light on. 2.Press the VIDEO 1 button, confirm display. 2CH and MOVIE LED light on. 3.Press the VIDEO 1 button, confirm display. SURROUND and MUSIC LED light on. SW L SL CR SSBSR L F E dB kHz mft. MHz DDDDSPSP ASP B OPT SLEEP COAXMULTI CH IN12 D.RANGEEQSTEREOMONORDS DIGITALMEMORYEXPROLOGICII DTS-ESNEO:6 MPEG-2 AAC L SL R SR dB Hz ft. SP ASP B COAX1D.RANGEEQMONO MEMORYEXII-ESNEO:6-2 SW C SSB L