JVC-MXDK11-cs-sm维修电路原理图.pdf

SERVICE MANUAL COPYRIGHT 2007 Victor Company of Japan, Limited No.MB598 2007/2 COMPACT COMPONENT SYSTEM MB59820072 SERVICE MANUAL MX-DK11A,MX-DK11UW, MX-DK11UX,MX-DK11UY, MX-DK11UG,MX-DK11UN COPYRIGHT 2007 Victor Company of Japan, Limited Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade) TABLE OF CONTENTS 1PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 2SPECIFIC SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 3DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-29 4ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-29 5TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-29 CA-MXDK11SP-MXDK11SP-MXDK11 RadioFans.CN 收音机爱 好者资料库 1-2 (No.MB598) SPECIFICATION *1: Measured at 1 kHz, with tape recording signal 400 mV. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Lab- oratories. DTS is a registered trademark of DTS, Inc. and DTS 2.0+Digital Out is a trademark of DTS, Inc. Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/ or other countries. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Design and specifications are subject to change without notice. Amplifier sectionOutput Power90 W per channel, min. RMS, driven into 6 at 1 kHz with no more than 10% total harmonic distortion. Digital outputOPTICAL DIGITAL OUTPUT : -21 dBm to -15 dBm (660 nm 30 nm) Audio input sensitivity/ Impedance *1 AUX : 400 mV/47 k MIC : 3.0 mV/50 k VIDEO OUTColor systemNTSC/PAL selectable VIDEO (composite)1 V(p-p)/75 S-VIDEOY (luminance) : 1 V(p-p)/75 C (chrominance, burst) : 0.286 V(p-p)/75 Speaker Terminals6 - 16 Tuner sectionFM tuning range87.50 MHz - 108.00 MHz AM (MW) tuning range531 kHz - 1 710 kHz (at 9 kHz) 530 kHz - 1 710 kHz (at 10 kHz) For Saudi Arabia only531 kHz - 1 602 kHz (at 9 kHz) 530 kHz - 1 600 kHz (at 10 kHz) Disc player sectionPlayable discDVD Video/CD/VCD/SVCD CD-R/-RW/-ROM (CD/VCD/SVCD/MP3/WMA/JPEG/MPEG-1/MPEG-2 format) DVD-R/-RW (DVD Video/DVD Video Recording (VR)/MP3/WMA/JPEG/MPEG-1/ MPEG-2 format) +R/+RW (DVD Video format) Dynamic range90 dB Horizontal resolution500 lines Wow and flutterImmeasurable Cassette deck section Frequency response Normal (type l) 50 Hz - 14 000 Hz Wow and flutter0.15% (WRMS) GeneralPower requirementAC 110 V / AC 127 V / AC 220 V / AC 230 V - AC 240 V , (adjustable with the voltage selector), 50 Hz / 60 Hz Power consumptionat operation: 95 W, on standby: 17 W Dimensions (approx.)265 mm 337 mm 370 mm (W/H/D) Mass (approx.)7.9 kg RadioFans.CN 收音机爱 好者资料库 (No.MB598)1-3 SECTION 1 PRECAUTION 1.1Safety Precautions (1) This design of this product contains special hardware and many circuits and components specially for safety purpos- es. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services should be per- formed by qualified personnel only. (2) Alterations of the design or circuitry of the product should not be made. Any design alterations of the product should not be made. Any design alterations or additions will void the manufacturers warranty and will further relieve the manufacture of responsibility for personal injury or property damage resulting therefrom. (3) Many electrical and mechanical parts in the products have special safety-related characteristics. These characteris- tics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by us- ing replacement components rated for higher voltage, watt- age, etc. Replacement parts which have these special safety characteristics are identified in the Parts List of Ser- vice Manual. Electrical components having such features are identified by shading on the schematics and by ( ) on the Parts List in the Service Manual. The use of a substitute replacement which does not have the same safety charac- teristics as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or other hazards. (4) The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to normal, after reassem- bling. (5) Leakage shock hazard testing After reassembling the product, always perform an isola- tion check on the exposed metal parts of the product (an- tenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.Do not use a line isolation transformer during this check. Plug the AC line cord directly into the AC outlet. Using a Leakage Current Tester, measure the leakage current from each exposed metal parts of the cabinet, particular- ly any exposed metal part having a return path to the chassis, to a known good earth ground. Any leakage cur- rent must not exceed 0.5mA AC (r.m.s.). Alternate check method Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 per volt or more sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15F AC-type capacitor between an ex- posed metal part and a known good earth ground. Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Voltage measured any must not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.). 1.2Warning (1) This equipment has been designed and manufactured to meet international safety standards. (2) It is the legal responsibility of the repairer to ensure that these safety standards are maintained. (3) Repairs must be made in accordance with the relevant safety standards. (4) It is essential that safety critical components are replaced by approved parts. (5) If mains voltage selector is provided, check setting for local voltage. 1.3Caution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of pre- forming repair of this system. 1.4Critical parts for safety In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the mark nearby are critical for safety. When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer. (This regulation dose not Except the J and C version) Good earth ground Place this probe on each exposed metal part. AC VOLTMETER (Having 1000 ohms/volts, or more sensitivity) 1500 10W 0.15 F AC TYPE 1-4 (No.MB598) 1.5Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products. Be careful to use proper grounding in the area where repairs are being performed. (1) Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. (2) Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body. (3) Handling the optical pickup In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) Do not use a tester to check the condition of the laser diode in the optical pickup. The testers internal power source can easily destroy the laser diode. 1.6Handling the traverse unit (optical pickup) (1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it. 1.7Attention when traverse unit is decomposed *Please refer to Disassembly method in the text for the pickup unit. Apply solder to the short land sections before the card wire is disconnected from the connecto on the servo board. (If the card wire is disconnected without applying solder, the pickup may be destroyed by static electricity.) In the assembly, be sure to remove solder from the short land sections after connecting the card wire. 1M Conductive material (conductive sheet) or iron palate (caption) Anti-static wrist strap DVD changer mechanism assembly Switch board DVD traverse mechanism assembly DVD servo board (No.MB598)1-5 1.8Important for laser products 1.CLASS 1 LASER PRODUCT 2.CAUTION : (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. (Others) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. 3.CAUTION : Visible and/or invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam. 4.CAUTION : This laser product uses visible and/or invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches. 5.CAUTION : If safety switches malfunction, the laser is able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure. REPRODUCTION AND POSITION OF LABELS and PRINT ! Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check. WARNING LABEL and PRINT 1-6 (No.MB598) SECTION 2 SPECIFIC SERVICE INSTRUCTIONS Please use the MX-DK1US service manual (No.MB515) excluding the published content as follows. The use number has changed when a part number of the reference origin and this part number are the same. Parts list (General assembly) P3-4 Block No.M1MM MX-DK11A MX-DK11UW ItemParts name Parts number Qty MX-DK1USMX-DK11A 1FRONT PANEL ASSYGV10328-001AGV10328-038A1 4FUNCTION BUTTONGV20418-002AGV20418-003A1 7FRONT LENSGV10319-001AGV10319-017A1 8VOLUME KNOBGV30875-001AGV30875-007A1 9V.ORNAMENT ASSYGV30894-001AGV30894-004A1 11MIC.KNOBGV40083-004A-0 14SPACERGV30349-068A-0 24TAP SCREWQYSBSF3010ZAQYSBSF3010ZA5 29SPACERGV30349-046A-0 31HEAT SINKGV30879-003AGV31012-001A1 32SCREWQYSBSG3016EAQYSBSG3016EA1 35SCREWQYSBSG3010EA-0 39SCREWQYSBSF3010ZA-0 40METAL COVERGV10217-007A/S/GV10217-015A/S/1 44REAR PANELGV10324-004AGV10324-047A1 47TUNERQAU0412-001QAU0492-0011 50TAP SCREWQYSBSGY3008EA-0 58TAP SCREWQYSDSG3006NAQYSDSG3008NA2 63POWER CORD(EU)QMPK200-200-JDQMPG150-244-JC1 64POWER TRANSQQT0515-001QQT0534-0011 66FFC WIREQUQU12-1911AJ-EQUQU12-1913AJ-E1 67FFC WIREQUQU12-1915BJ-EQUQU12-1921BJ-E1 68FFC WIREQUQU12-0915BJ-EQUQU12-0921BJ-E1 69FFC WIREQUR110-2520AJ-EQUR110-0532BJ-E1 70FFC WIREQUR110-0515AJ-EQUR110-2517AJ-E1 71FFC WIREQUR110-0532BJ-EQUR110-0513AJ-E1 78SPACERGV30349-048A-0 ItemParts name Parts number Qty MX-DK1USMX-DK11UW 1FRONT PANEL ASSYGV10328-001AGV10328-037A1 4FUNCTION BUTTONGV20418-002AGV20418-003A1 7FRONT LENSGV10319-001AGV10319-017A1 8VOLUME KNOBGV30875-001AGV30875-007A1 9V.ORNAMENT ASSYGV30894-001AGV30894-004A1 11MIC.KNOBGV40083-004AGV40083-006A1 14SPACERGV30349-068A-0 24TAP SCREWQYSBSF3010ZAQYSBSF3010ZA5 29SPACERGV30349-046A-0 31HEAT SINKGV30879-003AGV31012-001A1 (No.MB598)1-7 MX-DK11UX/UG 32SCREWQYSBSG3016EAQYSBSG3016EA1 35SCREWQYSBSG3010EA-0 39SCREWQYSBSF3010ZA-0 40METAL COVERGV10217-007A/S/GV10217-015A/S/1 44REAR PANELGV10324-004AGV10324-045A1 47TUNERQAU0412-001QAU0492-0011 58TAP SCREWQYSDSG3006NAQYSDSG3008NA2 64POWER TRANSQQT0515-001QQT0534-0011 66FFC WIREQUQU12-1911AJ-EQUQU12-1913AJ-E1 67FFC WIREQUQU12-1915BJ-EQUQU12-1921BJ-E1 68FFC WIREQUQU12-0915BJ-EQUQU12-0921BJ-E1 69FFC WIREQUR110-2520AJ-EQUR110-0532BJ-E1 70FFC WIREQUR110-0515AJ-EQUR110-2517AJ-E1 71FFC WIREQUR110-0532BJ-EQUR110-0513AJ-E1 78SPACERGV30349-048A-0 ItemParts name Parts number Qty MX-DK1USMX-DK11UX/UG 1FRONT PANEL ASSYGV10328-001AGV10328-037A1 4FUNCTION BUTTONGV20418-002AGV20418-003A1 7FRONT LENSGV10319-001AGV10319-017A1 8VOLUME KNOBGV30875-001AGV30875-007A1 9V.ORNAMENT ASSYGV30894-001AGV30894-004A1 11MIC.KNOBGV40083-004AGV40083-006A1 14SPACERGV30349-068A-0 24TAP SCREWQYSBSF3010ZAQYSBSF3010ZA5 29SPACERGV30349-046A-0 31HEAT SINKGV30879-003AGV31012-001A1 32SCREWQYSBSG3016EAQYSBSG3016EA1 35SCREWQYSBSG3010EA-0 39SCREWQYSBSF3010ZA-0 40METAL COVERGV10217-007A/S/GV10217-015A/S/1 44REAR PANELGV10324-004AGV10324-046A1 47TUNERQAU0412-001QAU0492-0011 58TAP SCREWQYSDSG3006NAQYSDSG3008NA2 64POWER TRANSQQT0515-001QQT0534-0011 66FFC WIREQUQU12-1911AJ-EQUQU12-1913AJ-E1 67FFC WIREQUQU12-1915BJ-EQUQU12-192