HarmanKardon-AVR445-avr-sm维修电路原理图.pdf

harman/kardon AVR445 AVR445 A/V DOLBY DIGITAL RECEIVER SERVICE MANUAL CONTENTS ESD WARNING.2 LEAKAGE TESTING.3 BASIC SPECIFICATIONS.4 PACKAGE.5 PACKAGE PARTS LIST.6 FRONT PANEL CONTROLS.7 REAR PANEL CONNECTIONS.10 REMOTE CONTROL FUNCTIONS.13 INSTALLATION/CONNECTIONS.17 OPERATION.20 TROUBLESHOOTING GUIDE.28 PROCESSOR RESET.28 UNIT EXPLODED VIEW29 EXPLODED VIEW PARTS LIST.30 BLOCK DIAGRAM(S)33 CIRCUIT DESCRIPTION.35 IDLE CURRENT ADJUST.36 SEMICONDUCTOR PINOUTS.39 PCB DRAWINGS.86 ELECTRICAL PARTS LIST.100 SCHEMATICS.122 WIRING DIAGRAM.137 harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev0 12/2006 RadioFans.CN 收音机爱 好者资料库 Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : AVR445 harman/kardonharman/kardon RadioFans.CN 收音机爱 好者资料库 2 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60Hz outlet and turn the AC power switch on. Any current measured must not exceed o.5mA. ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. Device under test Test all exposed metal surfaces Also test with plug reversed (Using AC adapter plug as required) AC Leakage Test Leakage current tester Reading should not be above 0.5mA Earth ground 3 AVR445 harman/kardonharman/kardon RadioFans.CN 收音机爱 好者资料库 62TECHNICAL SPECIFICATIONS AVR 445 TECHNICAL SPECIFICATIONS Audio Section Stereo Mode Continuous Average Power (FTC) 80 Watts per channel, 20Hz20kHz, <0.07% THD, both channels driven into 8 ohms Seven-Channel Surround Modes Power per Individual Channel Front L 1,025W at rated power output (7 channels driven) DimensionsProductShipping Width17-5/16 inches (440mm)20-1/16 inches (510mm) Height6-1/2 inches (165mm)10 inches (254mm) Depth17-1/16 inches (435mm)22-3/16 inches (565mm) Weight39 lb (17.7kg)46 lb (20.9kg) Depth measurement includes knobs, buttons and terminal connections. Height measurement includes feet and chassis. All features and specifications are subject to change without notice. Harman Kardon, Harman International and Logic 7 are registered trademarks of Harman International Industries, Incorporated. and are trademarks of Harman International Industries, Incorporated. Dolby, Pro Logic and the Double-D symbol are registered trademarks of Dolby Laboratories. Manufactured under license from Dolby Laboratories. DTS, DTS Surround, DTS-ES, DTS 96/24 and DTS Neo:6 are registered trademarks of DTS, Inc. A-BUS and A-BUS/READYare registered trademarks of Leisure Tech Electronics Pty Ltd Australia. SACD is a trademark of Sony Corporation. iPod and iTunes are registered trademarks of Apple Computer, Inc. HD-DVD is a trademark of the DVD Format/Logo Licensing Corporation (DVD FLLC). HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC. Microsoft,Windows and Windows Media are registered trademarks of Microsoft Corporation in the United States and other countries. XM Ready is a registered trademark of XM Satellite Radio, Inc. RealPlayer is a registered trademark of RealNetworks. Winamp is a registered trademark of America Online, Inc. TiVo is a registered trademark of TiVo Inc. The BridgeTM AVR445 OM 6/23/06 3:14 PM Page 62 4 AVR445 harman/kardonharman/kardon RadioFans.CN 收音机爱 好者资料库 AVR445 PACKAGING 5 AVR445 harman/kardonharman/kardon RadioFans.CN 收音机爱 好者资料库 AVR445 PACKAGE CHART Item# Part Number Description Qty 1 LABEL BARCODE AVR445 US (120v) 1 H03-RYD3101HA00-R LABEL BARCODE AVR445 EU TF PRINT (230v) 2 2 ZKD3194HA00-R BOX CARTON AVR445 US (120v) 1 ZKD3204HA01-R BOX CARTON AVR445 EU (230v) 1 3 ZKD3101HA00-R OWNERS MANUAL AVR445US (120v) 1 ZKD3201HA00-R OWNERS MANUAL AVR445EU (230v) 1 4 ZQD1201HAWH-R CUSHION POLY EPS RIGHT AVR445 1 5 FILM SHEET PE 920 X 1000 1 6 H03-WAUSA2103BK-R 120V POWER CORD WS-004C+002E SJT#14*2C L=2M 1 H03-WAD022000BK-R 230V POWER CORD WR002 H05VVF 0.75MMSQ 2G BLACK 2000MM 1 7 ZQD1202HAWH-R CUSHION POLY EPS LEFT AVR445 1 8 AVR445 TOTAL ACCESSORY BOX 1 9 RB18G00 REMOTE CONTROL AVR445 US (120v) 1 H03-RYD3201HA00-R REMOTE CONTROL AVR445 US (230v) 1 10 BAG PE 330 X245 T0.05 1 11 QUICK SETUP GUIDE AVR445 1 12 LABEL SAFETY LEAFLET 1 13 ZKC1113HA00-R CARD WARRANTY 1 14 BROCHURE AVR US 1 15 INSERT RS232 NOTE PAPER 1 16 H03-ZPD1212INBK-R MICROPHONE ASSY EXTENSION PIECE 1 17 BOX, ANTENNA 1 18 BAG PE 160X180MM 1 19 H03-WAB01200203-R ANTENNA WIRE 75 T15011N-1 US (120v) 1 H03-WAD01200303-R ANTENNA WIRE 75 OHM WIRE T15011F-1 EU (230v) 1 20 H03-ATALF039ABK-R ANTENNA WIRE ANTENNA LOOP-300 1 21 POLYBAG, BATTERY 1 22 BATTERY ALKALINE 1.5V AAA 2 23 BOX, ZONE II REMOTE CONTROL 1 24 RH15B00 REMOTE CONTROL ZONE 2 AVR445 (120v) 1 H03-RYD2702HA01-R REMOTE CONTROL ZONE 2 AVR445 (230v) 1 25 BOX, MIC 1 26 H03-MCD12TWBKNN AVR445 MICROPHONE ASSY 1 6 AVR445 harman/kardonharman/kardon RadioFans.CN 收音机爱 好者资料库 FRONT-PANEL CONTROLS 1 Standby/On Switch 2 Surround Mode Group Selector 3 Surround Mode Selector 4 Tuning Selector 5 Tuner Band Selector 6 Preset Station Selector 7 Input Source Selector 8 Tuning Mode Selector 9 Front-Panel Door ) Volume Control ! Input Indicators Speaker/Channel Input Indicators # Upper Display Line $ Lower Display Line % Surround Mode Indicators Remote Sensor Window FRONT-PANEL CONTROLS FRONT-PANEL CONTROLS5 5 The following controls and indicators are available on the AVR 445s front panel: The following controls and jacks are located behind the front-panel door.To open the door, place the edge of a finger on the left or right edge of the panel and gently swing the door down toward you. A Main Power Switch B Headphone Jack C Tone Mode Button D Speaker Selector Button E Channel Adjust Selector F Digital Input Selector G Delay Adjust Selector H / Buttons I Set Button J EzSet/EQ Microphone Jack K Optical 4 Digital Input L Coaxial 4 Digital Input M Input/Output Status Indicator N Video 4 Input/Output Jacks 1 Standby/On Switch: When the Main Power Switch A is “ON,” press this button to turn on the AVR 445; press it again to turn the unit off. Note that the illumination surrounding the switch will turn blue when the unit is on, or in the Multiroom mode. 2 Surround Mode Group Selector: Press this but- ton to select the top-level group of surround modes. Each press of the button will select one of the sur- round mode categories. Once the button is pressed so that the name of the desired surround mode category appears in the on-screen display and in the Lower Display Line $, press the Surround Mode Selector 3 to cycle through the individual modes available. For example, press this button to select Dolby modes, and then press the Surround Mode Selector 3 to choose from the various mode options. 3 Surround Mode Selector: Press this button to select from among the available surround mode options for the surround mode category selected. The specific modes will vary based on the number of speakers available, the surround mode category and whether the input source is digital or analog. For exam- ple, press the Surround Mode Group Selector 2 to select a category such as Dolby or Logic 7, and then press this button to see the specific mode choices that are available. For more information on mode selection, see pages 24, 35 and 58. NOTE: To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this product at . 245679 !#% 38 ABDE FGHHIJKLN M )$ 1 C AVR 445 XMFMAM USB DMP TAPE 8CH 6CH DVD DIGITAL PRO LOGIC IIx HEADPHONE VIRTUAL SPEAKER 57CH. STEREO DIRECT DSP SURR. OFF CDMI HDMI VID 34 VID 12 AVR445 OM 6/23/06 3:13 PM Page 5 7 AVR445 harman/kardonharman/kardon RadioFans.CN 收音机爱 好者资料库 FRONT-PANEL CONTROLS 6FRONT-PANEL CONTROLS 4 Tuning Selector: Press the left side of the button to tune lower-frequency stations and the right side of the button to tune higher-frequency stations.When the tuner is in the MANUAL/MONO mode, each tap of the Selector will increase or decrease the frequency by one increment.When the tuner receives a signal strong enough for adequate reception, MANUAL TUNED will appear in the Lower Display Line $ and in the on-screen display.When the tuner is in the AUTO/STEREO mode, press the button once, and the tuner will scan for a station with acceptable signal strength.When the next higher- or lower-frequency station is tuned, the frequency scan will stop and the Lower Display Line $ and the on-screen display will indicate AUTO TUNED.When an FM stereo station is tuned, the display will read AUTO ST TUNED. See page 39 for more information on using the tuner.When an XM Ready module is connected and activated, and when there is sufficient signal strength for the XM system to operate, pressing this button will also change the XM Radio channel. 5 Tuner Band Selector: Pressing this button will automatically switch the AVR 445 to the Tuner mode. Pressing it again will select the AM or FM frequency band, or XM Radio. (See page 39 for more informa- tion on the tuner.) 6 Preset Station Selector: Press this button to scroll up or down through the list of stations that have been entered into the preset memory. (See page 39 for more information on tuner programming.) 7 Input Source Selector: Press this button to change the input by scrolling up or down through the list of input sources. 8 Tuning Mode Selector: Press this button to select Auto or Manual tuning.When the button is pressed so that AUTO/STEREO appears in the Upper Display Line #, the tuner will search for the next station with an acceptable signal when the Tuning Selector 4Mis pressed.When the button is pressed so that MANUAL/MONO appears in the Upper Display Line #, each press of the Tuning Selector 4Mwill increase the frequency. (See page 39 for more information on using the tuner.) This button may also be used to switch between Stereo and Mono modes for FM radio reception.When weak reception is encountered, select the Manual/Mono tuning mode. Press and hold again to switch back to Stereo mode. (See pages 39 for more information on using the tuner.) When an optional XM Connect regardless of any changes, the display will always return to full-bright- ness when the AVR is turned on.The blue illumination around the Standby/On Switch 1 will always remain at full-brightness, regardless of the setting, to remind you that the AVR is still turned on.The blue accent lighting inside the volume control will also remain at full-brightness when the panel is at 50%, but go out when the panel lights are fully dimmed. ? Tuner/FM Select Button: This button functions in two ways. Press it up, toward the top of the remote, to select the tuner as the AVRs input.The first press will call up the last-used station (or XM channel). Subsequent presses will select the last-used FM,AM and XM Radio station or channel.When the button is pressed down, toward the bottom of the remote, the last-tuned FM station is selected as the AVRs input. ?Channel Up/Down Selector: This button has no function when the AVR is being controlled, but when programmed for use with a VCR,TV, cable box, satel- lite receiver or other similar product, it will change the channel up or down. See pages 4656 for more information on programming the remote. ? Delay Select Button: This button selects adjustments to the A/V Sync Delay and the individual channel displays.The first press of the button displays an A/V SYNC DELAY message in the Lower Display Line $ and in the on-screen display, which means that you may change the amount of time that all channels are delayed together behind the video. This enables you to compensate for the loss of lip sync that may be caused by digital vide