HarmanKardon-AVR255.230-avr-sm维修电路原理图.pdf

harman/kardon Service Manual AVR 255/230 7 x 50W 7.1 CHANNEL A/V RECEIVER CONTENTS ESD WARNING 2 BASIC SPECIFICATIONS 3 TROUBLESHOOTING GUIDE 4 PROCESSOR RESET 4 REMOTE RESET 5 PACKAGE LIST AND PARTS 6 DISASSEMBLY 7 EXPLODED VIEW AND PARTS 8 ELECTRICAL PARTS LIST 9 SEMICONDUCTOR PINOUTS 50 PCB DRAWINGS 121 BLOCK DIAGRAM 129 WIRING DIAGRAM 130 AMP BIAS ADJUSTMENT 131 SCHEMATIC DIAGRAMS 132 Released EU2008 harman/kardon, Inc. Rev 0, 07/2008 250 Crossways Park Dr. Woodbury, New York, 11797 harman/kardonAVR 255/230 Service Manual Page 1 of 144 RadioFans.CN 收音机爱 好者资料库 Eachprecautioninthismanualshouldbefollowedduringservicing. Components identified with the IEC symbolin the parts list are special significance to safety. When replacing a component identified with , use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before retuming the product to the customer. Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor chip components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build-up or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices. CAUTION : harman/kardonAVR 255/230 Service Manual Page 2 of 144 RadioFans.CN 收音机爱 好者资料库 2 TECHNICAL SPECIFICATIONS 57 ENGLISH Technical Specifications Audio Section Stereo Mode Continuous Average Power (FTC) 65Watts per channel, 20Hz20kHz, < 0.07% THD, both channels driven into 8 ohms 7 Channel Surround Modes Power Per Individual Channel, all channels driven simultaneously: Front L MM 200V DESCRIPTION The 74LCX32 is a low voltage CMOS QUAD 2-INPUT OR GATE fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power and high speed 3.3V applications; it can be interfaced to 5V signal environment for inputs. It has same speed performance at 3.3V than 5V AC/ACT family, combined with a lower power consumption. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. 74LCX32 LOW VOLTAGE CMOS QUAD 2-INPUT OR GATE WITH 5V TOLERANT INPUTS Figure 1: Pin Connection And IEC Logic Symbols Table 1: Order Codes PACKAGET UDQS correspond to the data on DQ8-DQ15 SYMBOLTYPEDESCRIPTION DM (x8) Input Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH along with that input data during a WRITE access. DM is sampled on both edges of DQS. Although DM pins are input only, the DM loading matches the DQ and DQS loading. For the x16, LDM corresponds to the data on DQ0-DQ7; UDM corresponds to the data on DQ8-DQ15. Input / Output VrefInputSSTL_2 reference voltage. UDQS, LDQS (x16) UDM, LDM (x16) harman/kardonAVR 255/230 Service Manual Page 58 of 144 RadioFans.CN 收音机爱 好者资料库 DS586PP517 CS42528 2. PIN DESCRIPTIONS Pin Name#Pin Description CX_SDIN1 CX_SDIN2 CX_SDIN3 CX_SDIN4 1 64 63 62 Codec Serial Audio Data Input (Input) - Input for twos complement serial audio data. CX_SCLK2CODEC Serial Clock (Input/Output) - Serial clock for the CODEC serial audio interface. CX_LRCK3CODEC Left Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on the CODEC serial audio data line. VD4 51 Digital Power (Input) - Positive power supply for the digital section. DGND5 52 Digital Ground (Input) - Ground reference. Should be connected to digital ground. VLC6Control Port Power (Input) - Determines the required signal level for the control port. SCL/CCLK7Serial Control Port Clock (Input) - Serial clock for the serial control port. Requires an external pull-up resistor to the logic interface voltage in I2C mode as shown in the Typical Connection Diagram. SDA/CDOUT8Serial Control Data (Input/Output) - SDA is a data I/O line in I2C mode and requires an external pull-up resistor to the logic interface voltage, as shown in the Typical Connection Diagram. CDOUT is the output data line for the control port interface in SPI mode. AD1/CDIN9Address Bit 1 (I2C)/Serial Control Data (SPI) (Input) - AD1 is a chip address pin in I2C mode; CDIN is the input data line for the control port interface in SPI mode. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1718 1920 212223242526272829303132 64636261 605958575655545352515049 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 CX_SDIN1 SAI_SCLK SAI_LRCK VD DGND VLC SCL/CCLK SDA/CDOUT AD1/CDIN AD0/CS INT RST AINR- AINR+ AINL+ AINL- VQ FILT+ REFGND AOUTB4- AOUTB4+ AOUTA4+ AOUTA4- VA AGND AOUTB3- AOUTB3+ AOUTA3+ AOUTA3- AOUTB2- AOUTB2+ AOUTA2+ AOUTA2- AOUTB1- AOUTB1+ AOUTA1+ AOUTA1- MUTEC AGND VARX RXP7/GPO7 RXP6/GPO6 RXP5/GPO5 RXP4/GPO4 RXP3/GPO3 RXP2/GPO2 RXP1/GPO1 LPFLT RXP0 TXP VD DGND VLS SAI_SDOUT RMCK CX_SDOUT ADCIN2 ADCIN1 OMCK CX_LRCK CX_SCLK CX_SDIN4 CX_SDIN3 CX_SDIN2 CS42528 harman/kardonAVR 255/230 Service Manual Page 59 of 144 RadioFans.CN 收音机爱 好者资料库 CS42528 18DS586PP5 AD0/CS10 Address Bit 0 (I2C)/Control Port Chip Select (SPI) (Input) - AD0 is a chip address pin in I2C mode; CS is the chip select signal in SPI mode. INT11Interrupt (Output) - The CS42528 will generate an interrupt condition as per the Interrupt Mask register. See “Interrupts” on page 40 for more details. RST12Reset (Input) - The device enters a low power mode and all internal registers are reset to their default settings when low. AINR- AINR+ 13 14 Differential Right Channel Analog Input (Input) - Signals are presented differentially to the delta-sigma modulators via the AINR+/- pins. AINL+ AINL- 15 16 Differential Left Channel Analog Input (Input) - Signals are presented differentially to the delta-sigma modulators via the AINL+/- pins. VQ17Quiescent Voltage (Output) - Filter connection for internal quiescent reference voltage. FILT+18Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling circuits. REFGND19Reference Ground (Input) - Ground reference for the internal sampling circuits. AOUTA1 +,- AOUTB1 +,- AOUTA2 +,- AOUTB2 +,- AOUTA3 +,- AOUTB3 +,- AOUTA4 +,- AOUTB4 +,- 36,37 35,34 32,33 31,30 28,29 27,26 22,23 21,20 Differential Analog Output (Output) - The full-scale differential analog output level is specified in the Analog Characteristics specification table. VA VARX 24 41 Analog Power (Input) - Positive power supply for the analog section. AGND25 40 Analog Ground (Input) - Ground reference. Should be connected to analog ground. MUTEC38Mute Control (Output) - The Mute Control pin outputs high impedance following an initial power-on con- dition or whenever the PDN bit is set to a 1, forcing the codec into power-down mode. The signal will remain in a high impedance state as long as the part is in power-down mode. The Mute Control pin goes to the selected “active” state during reset, muting, or if the master clock to left/right clock frequency ratio is incorrect. This pin is intended to be used as a control for external mute circuits to prevent the clicks and pops that can occur in any single supply system. The use of external mute circuits are not manda- tory but may be desired for designs requiring the absolute minimum in extraneous clicks and pops. LPFLT39PLL Loop Filter (Output) - An RC network should be connected between this pin and ground. RXP7/GPO7 RXP6/GPO6 RXP5/GPO5 RXP4/GPO4 RXP3/GPO3 RXP2/GPO2 RXP1/GPO1 42 43 44 45 46 47 48 S/PDIF Receiver Input/ General Purpose Output (Input/Output) - Receiver inputs for S/PDIF encoded data. The CS42528 has an internal 8:2 multiplexer to select the active receiver port, according to the Receiver Mode Control 2 register. These pins can also be configured as general purpose output pins, ADC Overflow indicators or Mute Control outputs according to the RXP/General Purpose Pin Control registers. RXP049S/PDIF Receiver Input (Input) - Dedicated receiver input for S/PDIF encoded data. TXP50S/PDIF Transmitter Output (Output) - S/PDIF encoded data output, mapped directly from one of the receiver inputs as indicated by the Receiver Mode Control 2 register. VLS53Serial Port Interface Power (Input) - Determines the required signal level for the serial port interfaces. SAI_SDOUT54Serial Audio Interface Serial Data Output (Output) - Output for twos complement serial audio PCM data from the S/PDIF incoming stream. This pin can also be configured to transmit the output of the inter- nal and external ADCs. RMCK55Recovered Master Clock (Output) - Recovered master clock output from the External Clock Reference (OMCK, pin 59) or the PLL which is locked to the incoming S/PDIF stream or CX_LRCK. harman/kardonAVR 255/230 Service Manual Page 60 of 144 RadioFans.CN 收音机爱 好者资料库 DS586PP519 CS42528 CX_SDOUT56CODEC Serial Data Output (Output) - Output for twos complement serial audio data from the internal and external ADCs. ADCIN1 ADCIN2 58 57 External ADC Serial Input (Input) - The CS42528 provides for up to two external stereo analog to digital converter inputs to provide a maximum of six channels on one serial data output line when the CS42528 is placed in One Line mode. OMCK59External Reference Clock (Input) - External clock reference that must be within the ranges specified in the register “OMCK Frequency (OMCK Freqx)” on page 54. SAI_LRCK60Serial Audio Interface Left/Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on the serial audio data line. SAI_SCLK61Serial Audio Interface Serial Clock (Input/Output) - Serial clock for the Serial Audio Interface. harman/kardonAVR 255/230 Service Manual Page 61 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 62 of 144 RadioFans.CN 收音机爱 好者资料库 ESIESIESIESI 3 Rev. 0A May 25, 2006 ES29LV320E Excel Semiconductor inc. PRODUCT SELECTOR GUIDE Family Part NumberES29LV320E Voltage Range2.7V 3.6 V Speed Option7090 Max Access Time (ns)7090 CE# Access (ns)7090 OE# Access (ns)3040 Command Register Analog Bias Generator Address Latch BYTE# CE# OE# A RESET# Vcc Vss Chip Enable Output Enable Logic Vcc Detector Timer/ Counter Y-Decoder X-Decoder Y-Decoder Cell Array Data Latch/ Sense Amps Input/Output Buffers Sector Switches DQ0-DQ15(A-1) RY/BY# Write State Machine WE# FUNCTION BLOCK DIAGRAM harman/kardonAVR 255/230 Service Manual Page 63 of 144 RadioFans.CN 收音机爱 好者资料库 ESIESIESIESI 4 Rev. 0A May 25, 2006 ES29LV320E Excel Semiconductor inc. PIN DESCRIPTION PinDescription A0-A2021 Addresses DQ0-DQ1415 Data Inputs/Outputs DQ15/A-1 DQ15 (Data Input/Output, Word Mode) A-1 (LSB Address Input, Byte Mode) CE#Chip Enable OE#Output Enable WE#Write Enable WP#/ACCHardware Write Protect/Acceleration Pin RESET#Hardware Reset Pin, Active Low BYTE#Selects 8-bit or 16-bit mode RY/BY#Ready/Busy Output Vcc 3.0 volt-only single power supply (see Product Selector Guide for speed options and voltage supply tolerances) VssDevice Ground NCPin Not Connected Internally LOGIC SYMBOL DQ0 DQ15 (A-1) RY/BY# BYTE# RESET# OE# CE# A0 A20 WP#/ACC WE# 21 16 or 8 harman/kardonAVR 255/230 Service Manual Page 64 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 65 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 66 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 67 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 68 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 69 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 70 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 71 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 72 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 73 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 74 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 75 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 76 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 77 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 78 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 79 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 80 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 81 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 82 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 83 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 84 of 144 RadioFans.CN 收音机爱 好者资料库 harman/kardonAVR 255/230 Service Manual Page 85 of 144 RadioFans.CN