HarmanKardon-AVR134-avr-sm维修电路原理图.pdf
RadioFans.CN 收音机爱 好者资料库 SAFETY PRECAUTIONS WARNING Before servicing this unit, familiarize yourself with the following precautions: 1. Many electrical and mechanical parts in this chassis have special safety characteristics that often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements: electrical components having such features are identified by in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards. 2. Before returning the set to the customer, always do an AC leakage current check on the exposed metal parts of the cabinet, such as terminals, screw heads, and metal overlays, to be sure the set is safe to operate danger of electrical shock. Plug the AC line cord directly into a 120 V AC outlet(USA Version) or 230 V AC outlet(EU Version). (Do not use a line isolation transformer during this check.) Be sure your AC voltmeter has a sensitivity of 5000 per volt or greater. Then connect a 1500 10 watt resistor, paralleled by a 0.15 F 150 V AC capacitor, between a known good earth ground(such as a water pipe, or conduit) and the exposed metallic parts, one at a time. Measure the AC voltage across the combination of a 1500 resistor and a 0.15 F capacitor. Reverse the AC plug at the AC outlet and repeat AC voltage measurements for each exposed metalic part. Voltage measured must not exceed 0.75 V RMS. This corresponds to 0.2 mA AC. Any value exceeding this limit constitutes a potential shock hazard and must be corrected immediately. 2 RadioFans.CN 收音机爱 好者资料库 Measuring methods are based on IHF and IEC standard 268-3 Measurements conditions,unless otherwise noted : Output resistive load = (6) ohms / Both channel driven Tone Direct ON , Other SWs : OFF Power figures should be kept minimum 10min. between 15 and 35c Filter : IHF-A filter,R/O = Rated Output Power supply : 240 V / 50 Hz 1. FRONT AMP SECTION *SPKR LEVEL : ALL 0dB *SPK SIZE:LLLY *6CH INPUT *TONE OFF INPUTFREQ.REMARKUNITNOMINALLIMIT 1INPUT SENSITIVITY6CH INPUT1kHzR/OmV2003020050 TOTAL HARMONIC DISTORTION6CH INPUT20HzR/O-3dB% 0.07 0.09 (STEREO IN)1kHzR/O-3dB% 0.07 0.09 20KHzR/O-3dB% 0.07 0.09 CONTINUOUS AVERAGE POWER 6CH INPUT20Hz(6)ohmsW7572 at 0.1% THD1kHz?W7572 (STEREO IN)20kHz?W7572 S/N RATIO, INPUT SHORT6CH INPUT1kHzR/OdB 90 85 IHF-A FILTER FREQUENCY RESPONSE (-3dB)6CH INPUT1W/1KHz Ref.HzkHz20552050 2. CENTER AMP SECTION *SPKR LEVEL : ALL 0dB *SPK SIZE:LLLY *6CH INPUT *TONE OFF INPUTFREQ.REMARKUNITNOMINALLIMIT 1INPUT SENSITIVITY6CH INPUT1kHzR/OmV2003020050 TOTAL HARMONIC DISTORTION6CH INPUT20HzR/O-3dB% 0.07 0.09 (STEREO IN)1kHzR/O-3dB% 0.07 0.09 20kHzR/O-3dB% 0.07 0.09 CONTINUOUS AVERAGE POWER 6CH INPUT20Hz(6)ohmsW7572 at 0.1% THD1kHz?W7572 (STEREO IN)20kHz?W7572 S/N RATIO, INPUT SHORT6CH INPUT1kHzR/OdB 90 85 IHF-A FILTER 5FREQUENCY RESPONSE (-3dB)6CH INPUT1W/1kHz Ref.HzkHz20552050 DESCRIPTION DESCRIPTION 2 3 4 5 2 3 4 3 SPECIFICATION RadioFans.CN 收音机爱 好者资料库 3. SURROUND AMP SECTION *SPKR LEVEL : ALL 0dB *6CH INPUT INPUTFREQ.REMARKUNITNOMINALLIMIT 1INPUT SENSITIVITY6CH INPUT1kHzR/OmV2003020050 TOTAL HARMONIC DISTORTION6CH INPUT20HzR/O-3dB%?0.07?0.09 (STEREO IN)1kHzR/O-3dB%?0.07?0.09 20kHzR/O-3dB%?0.07?0.09 CONTINUOUS AVERAGE POWER 6CH INPUT20Hz(6)ohmsW7572 at 0.1% THD1kHz?W7572 (STEREO IN)20kHz?W7572 S/N RATIO, INPUT SHORT6CH INPUT1kHzR/OdB?90?85 IHF-A FILTER FREQUENCY RESPONSE (-3dB)6CH INPUT1W/1kHz Ref.HzkHz20552050 4. SUBWOOFER SECTION *SPKR LEVEL : ALL 0dB *6CH INPUT INPUTFREQ.REMARKUNIT *TONE OFF NOMINALLIMIT 1PRE OUTPUT LEVELSUB-CH(200mV)30HzVOL max.V1.70.51.71.0 5. STEREO SECTION *SPKR LEVEL : ALL 0dB *TONE OFF(TONE DIRECT) INPUTFREQ.REMARKUNITNOMINALLIMIT 1INPUT SENSITIVITY CD1kHzmV2003020050 2CHANNEL BALANCE CD1kHzR/O TO -40dBdB23 4RESIDUAL NOISE 1kHzVOL min.mV?1.0?1.2 5TOTAL HARMONIC DISTORTION(20)HzR/O-3dB%?0.07?0.09 CD 1kHz?%?0.07?0.09 (20)kHz?%?0.07?0.09 6CONTINUOUS AVERAGE POWER (20)Hz(6)ohmsW7572 at 0.1% THDCD1kHz?W7572 (20)kHz?W7572 8S/N RATIO,IHF-A FILTER1kHzR/OdB?90?85 9CHANNEL SEPARATION100HzR/O-3dBdB?57?50 CD1kHz?dB?57?55 10kHz?dB?57?55 10FUNCTION CROSSTALKCD?TAPE 1kHz?dB?65?60 10kHz?dB?45?40 11FREQUENCY RESPONSE (-3dB)CD 1WHzkHz20552050 12TONE CONTROL , (12)dB100Hz1WdB12(2)12(3) (TONE ON) 10kHz?dB12(2)12(3) 13HEADPHONE OUTPUT CD1kHzR/OV2.50.52.51.0 H/P = 64ohms CD CD CD DESCRIPTION DESCRIPTION DESCRIPTION 2 3 4 5 *SPK SIZE:LLLY *SPK SIZE:LLLY *TONE OFF *SPK SIZE:LLLY 4 RadioFans.CN 收音机爱 好者资料库 6. Idle Voltage *SPKR LEVEL : ALL 0dB *6CH Input *TONE OFF(TONE DIRECT), *TEST BD : AMP *Test Point : R221(FL,FR,SL,SR,C) Both Sides Voltage(DC). NO.INPUTFREQ.REMARKUNITNOMINALLIMIT 1FL-R221FLmV2.70.32.70.5 2FR-R221FRmV2.70.32.70.5 3SL-R221SLmV2.70.32.70.5 4SR-R221SRmV2.70.32.70.5 5C-R221CmV2.70.32.70.5 7. DOLBY DIGITAL INPUT SECTION INPUT : COAXIAL (CD DIGITAL)VOLUME POSISTION : -18dB SURROUND MODE : DOLBY DIGITALAT SPEAKER OUT Disc : LD VER 1.0 NOINPUTFREQ.CHAPUNITNOMINALLIMIT OUT PUT LEVELFRONT1kHz8 ,12V9.519.52 Disc All CH 0dBCENTER1kHz10V9.519.52 SPK MODE:LLLYSURR1kHz14,16V9.519.52 S/W30Hz18V1.00.31.00.4 T.H.DFRONT1kHz38?0.3?0.5 Disc 0dBCENTER1kHz38?0.3?0.5 LPF(20kHz)SURR1kHz38?0.3?0.5 SPK MODE:LLLYS/W30Hz18?0.25?0.3 S/NFRONT1kHz6dB?65?60 LPF(20kHz)CENTER1kHz6dB?65?60 JIS-A FILTER, Disc -20dBSURR1kHz6dB?65?60 SPK MODE : LLLYS/W30Hz18dB?65?60 DYNAMIC RANGEFRONT1kHz38dB-111-112 CENTER1kHz38dB-111-112 SURR1kHz38dB-111-112 S/W30Hz18dB0102 DIALOG FRONT43dB-100.5-101 NORMALIZATIONCENTER43dB-100.5-101 SURR43dB-100.5-101 S/W43dB-100.5-101 OUTPUT CONFIG 1FRONT1kHz38(ref)dB-171-173 SPK MODE : SSSY20 Ref : 1KHz 0dBCENTER1kHz38(ref)dB-171-173 20 SURR1kHz38(ref)dB-171-173 20 Ref : 30Hz 0dBS/W30Hz18(ref)dB6.016.02 22 OUTPUT CONFIG 2FRONT1kHz38(ref)dB5.515.52 SPK MODE : LSSN18 DOWNMIXING TESTCENTER1kHz10(ref)dB-30.5-31 SPK MODE : LSSYC-NO SURR.L1kHz14dB-30.5-31 LS-NO SURR.R1kHz16dB-30.5-31 RS-NO FRONT1kHz6(ref)dB7.517.52 ST:ON 7 8 DESCRIPTION 1 2 3 4 5 6 CHANNEL *SPK SIZE:LLLY*Main Vol : -18dB 5 RadioFans.CN 收音机爱 好者资料库 8. DTS INPUT SECTION INPUT : COAXIAL, CD DIGITALVOLUME POSISTION : -18dB SURROUND MODE : DTS SURROUND AT PREOUT SPK MODE LLLY DTS TEST Disc(TRACK 9,10,11,12,13,14,15) NOINPUTFREQ.TRACKUNITNOMINALLIMIT OUTPUT LEVELFRONT1kHz 1kHz 1kHz 1kHz 1kHz 1kHz 1kHz 1kHz 1kHz 10,11V9.519.52 Disc : DTS 0dBCENTER14V9.519.52 LLLYSURR12,13V9.519.52 S/W30kHz15V1.00.31.00.4 THD FRONT10,11?0.3?0.5 Disc : DTS 0dBCENTER14?0.3?0.5 LPF(20KHz)SURR12,13?0.3?0.5 LLLYS/W30kHz15?0.3?0.5 S/N FRONT10,11dB?65?60 Disc 0dB,JIS ACENTER14dB?65?60 LPF(20KHz)SURR12,13dB?65?60 LLLYS/W30kHz15dB?65?60 1 2 3 DESCRIPTION 6 RadioFans.CN 收音机爱 好者资料库 Measuring methods in confirmity with IEC standard 315 Measurements condition FM : Ref. frequency = ( 98.1 MHz), Audio frequency = 1kHz Reference level = 1 mV on (75ohms, 300ohms) Deviation : Filter = B.P.F at STEREO and MONO Test Point : TP1 = 90.1 MHz, TP2 = 98.1 MHz, TP3 = 106.1 MHz(50kHz STEP) MOD:40 kHz(Mono)/40 kHz7.5 kHz (STEREO) 9. FM SECTION NOUNITNOMINALLIMIT 1TUNING COVER RANGELOW HIGHMHz STEPAUTO/MANUALkHz 2USABLE SENSITIVITYTP 1dBu?12?15 S/N = 30TP 2dBu ?12?15 TP 3dBu?12?15 3AUTO STOP LEVELdBu256258 4S/N RATIO MONOdBu?55?50 IHF ASTEREOdBu?50?45 5T.H.DMONO 1, 1kHz?0.7?1.2 STEREO 1, 1kHz? ?1.0?1.5 6OVER LOAD DISTORTION (120dBu,75kHz)MONOdB?2?3 7STEREO SEPARATION250?dBu?30?25 (MAIN 53.5%, PILOT 10%)dBu?30?25 EXT 19kHz FILTER6.3dBu?20?15 8FREQUENCY RESPONSE (50us, -3dB)TP 2Hz608k707k 9IF REJECTIONTP 1dB?75?70 10IMAGE REJECTIONTP 3dB?75?70 11AM SUPRESSION (at AM 30% 1kHz)dB?40?35 12OUPUT LEVEL(MONO)TP 2mV rms28050280100 DESCRIPTION 87.5108 50/50(200/200 Brasil) 7 RadioFans.CN 收音机爱 好者资料库 10. AM SECTION Measurements condition AM - MW : Radio. frequency = 1000/999 kHz , Audio frequency = 400 Reference level = (74dBu/m),(50)ohmsModulation = ( 30 )% Test Point : MW TP 1 = (594/600) kHz , TP 2 = (999/1000) kHz , TP 3 = (1404/1400) kHz NOUNITNOMI.LIMIT 1TUNING COVER RANGELOWHIGH MW STEPAUTO/MANUAL 2USABLE SENSITIVITYTP 1 kHz kHz dBu/m dBu/m dBu/m dB % % % dB dB dB ?63?65 TP 2?63?65 , S/N = 20dB TP 3?63?65 3S/N RATIO TP 2?35?30 100 dBu/m, 30% MOD 4T.H.D TP 2?2?3 74 dB u/m, 30% MOD 5OVER LOAD DISTORTION TP 2?3?5 100 dB u/m ,80% MOD 6FREQUENCY RESPONSE AT-6dBHZ802K1001.8K (at 74 dBu/m, 400 Hz) - NO FILTER 7SELECTIVITYTP 2?23?20 at SN: 20dB, 9KHz 8AGC FIGURE OF MERITTP 2?50?40 (at 100 dB/m) 9IMAGE REJECTIONTP 3?28?25 10WHISTLE MODULATION2IF?10?15 (74dB u/m,900kHz) 11TUNED LEVELdBu/m55105515 999kHz 12AUTO STOP LEVEL999?dBu/m55105515 13OUTPUT LEVELmVrms18060180100 74 dB u/m, 30 % MOD DESCRIPTION 9/9(10/10 Brazil) 5221620(5201710 Brasil) 8 RadioFans.CN 收音机爱 好者资料库 9 CIRCUIT DESCRIPTION UPD78F0536GK : IC101 1. Pin Description RadioFans.CN 收音机爱 好者资料库 10 2. Block Diagram 16-bit TIMER/ EVENT COUNTER 00 16-bit TIMER/ EVENT COUNTER 01 TO00/TI010/P01 TI000/P00 (LINSEL) RxD6/P14 (LINSEL) TO01Note 2/TI011Note 2/P06 TI001Note 2/P05 TOH0/P15 TOH1/P16 TI50/TO50/P17 TI51/TO51/P33 RxD0/P11 TxD0/P10 RxD6/P14 TxD6/P13 SI10/P11 SO10/P12 SCK10/P10 8-bit TIMER H0 8-bit TIMER H1 WATCHDOG TIMER WATCH TIMER INTERNAL LOW-SPEED OSCILLATOR SERIAL INTERFACE UART0 78K/0 CPU CORE BANK SERIAL INTERFACE UART6 LINSEL SERIAL INTERFACE CSI10 8-bit TIMER/ EVENT COUNTER 50 8-bit TIMER/ EVENT COUNTER 51 SERIAL INTERFACE IIC0 A/D CONVERTER SERIAL INTERFACE CSI11 Notes 1. Available only in the PD78F0536, 78F0537, and 78F0537D. 2. Available only in the PD78F0534, 78F0535, 78F0536, 78F0537, and 78F0537D. 3. Available only in the PD78F0537D. Note2 Note2 Note1 Note2 Note2 Note3 8 INTERRUPT CONTROL 2 4 PORT 07P00 to P06 PORT 18P10 to P17 PORT 28P20 to P27 PORT 34P30 to P33 PORT 44P40 to P43 PORT 54P50 to P53 PORT 64P60 to P63 PORT 78P70 to P77 PORT 125P120 to P124 PORT 13P130 PORT 142P140, P141 BUZZER OUTPUT BUZ/P141 CLOCK OUTPUT CONTROL PCL/P140 KEY RETURN8 KR0/P70 to KR7/P77 RESET CONTROL MULTIPLIER & DIVIDER ON-CHIP DEBUG SYSTEM CONTROL INTERNAL HIGH-SPEED OSCILLATOR VOLTAGE REGULATOR POWER ON CLEAR/ LOW VOLTAGE INDICATOR EXLVI/P120 RESET REGC X1/P121 X2/EXCLK/P122 XT1/P123 XT2/EXCLKS/P124 POC/LVI CONTROL FLASH MEMORY INTERNAL HIGH-SPEED RAM INTERNAL EXPANSION RAM VDD, EVDD VSS, EVSS FLMD0 OCD0ANote 3/X1, OCD1ANote 3/P31 OCD0BNote 3/X2, OCD1BNote 3/P32 SI11Note 2/P03 SO11Note 2/P02 SCK11Note 2/P04 SSI11Note 2/P05 EXSCL0/P62 SDA0/P61 SCL0/P60 ANI0/P20 to ANI7/P27 AVREF AVSS RxD6/P14 (LINSEL) INTP0/P120 (LINSEL) INTP1/P30 to INTP4/P33 INTP5/P16 INTP6/P140, INTP7/P141 RadioFans.CN 收音机爱 好者资料库 11 3. Pin Functions No.Pin NamePin SymbolI/OPin Description 1P120/INTP0/EXLVIPROTECTIONIInput for protection 2P43VOL_UPIInput for volume up 3P42VOL_DNIInput for volume down 4P41H/P_RLYOOutput for headphone relay 5P40C_RLYOOutput for center speaker relay 6RESETRESETIInput for u-com reset 7P124/XT2/EXCLKSS_RLYOOutput for surround speaker relay 8P123/XT1F_RLYOOutput for front speaker relay 9IC/FLMD0FLMD0OPort for flash mode setting 10P122/X2/EXCLKV1 OUT_MUTEOOutput for VIDEO1 OUT MUTE 11P121/X1TRIG CONTROLOOutput for DC TRIGGER ON/OFF 12REGCConnect to ground via 0.47uF/50V E.Cap 13VSSVSSGround 14EVSSEVSSGround 15VDDVDD3V3 16EVDDEVDD3V3 17P60/SCLOVIDEO_MUTEOOutput for video mute 18P61/SDA0VIDEO_S1/HDMI_S2OOutput for video/HDMI function IC switching 19P62/EXSCL0VIDEO_S2/HDMI_S1OOutput for video/HDMI function IC switching 20P63TUNEDIInput for tuner TUNED condition (L is active) 21P33/TI51/TO51/INTP4RDS_CLKIClock signal input from tuner pack 22P77/KR7RDS_DATAIInput for RDS data from tuner pack 23P76/KR6PLL_CEOChip select output for tuner pack 24P75/KR5PLL_DOOData output for tuner pack 25P74/KR4SW_MUTEOOutput for subwoofer channel mute 26P73/KR3C_MUTEOOutput for center channel mute 27P72/KR2S_MUTEOOutput for surround channel mute 28P71/KR1F_MUTEOOutput for front channel mute 29P70/KR0USB_PCOOutput for IC108(REGULATOR) ON/OFF 30P06/TI011/TO01R2A1521FP_CLKOClock signal output for R2A1521FP 31P05/TI001/SSI11R2A1521FP_DATAOOutput for R2A1521FP control data 32P32/INTP3P32Port for flash upgrade 33P31/INTP2P31Port for flash upgrade 34P50DSP/DIR_CCLKOClock signal output for DIR/DSP 35P51DSP/DIR_CDINI/OInput & output for DIR/DSP control data 36P52DSP_RESETOOutput for DSP reset RadioFans.CN 收音机爱 好者资料库 12 39P17/TI50/TO05DSP_ABOOTOOuput for DSP Auto boot 40P16/TOH1/INTP5DSP_INTREQIInterrupt signal output to DSP 41P15/TOH0DIR_PDNOOutput for DIR power down 42P14/RXD6RxDIInput for flash upgrade 43P13/TXD6TxDOOutput for flash upgrade 44P12/SO10Front B RLYOOutput for SPK B ON/OFF 45P11/SI10/RXD024C08_SCLKOClock signal output for 24C08 46P10/SCK10/TXD024C08_SDAI/OInput & output for 24C08 control data 47AVREFAVREF3V3 48AVSSAVSSGROUND 49P27/ANI7KEY2IInput for KEY2 scan 50P26/ANI6KEY3IInput for KEY3 scan 51P25/ANI5KEY1IInput for KEY1 scan 52P24/ANI4BT/THERMAL_DETIBLUETOOTH DETECT 53P23/ANI3HDMI_HPDOOuput for HDMI HPD(NOT USED) 54P22/ANI2HDMI_S2OOuput for HDMI S2 CONTROL(NOT USED) 55P21/ANI1HDMI_S2OOuput for HDMI S1 CONTROL(NOT USED) 56P20/ANI0FUNC_DNIInput for function encoder down 57P130ST/BY_LEDOOuput for standby led 58P04/SCK11ST/BY_RLYOOnput for standby relay 59P03/S111FUNC_UPIInput for function encoder up 60P02/S011FLT/PLL_DATAOOutput for FLT/PLL control data 61P01/TI010/TO00FLT/PLL_CLKOClock signal output for FLT/PLL 62P00/TI000RMCIInput for remocon data 63P141/BUZ/INTP7FLT_CEOChip select output for FLT 64P140/PCL/INTP6POWER_DOWNIInput for power down No.Pin NamePin SymbolI/OPin Description 37P53DSP_RDYIInput for DSP enable 38P30/INTP1DSP_CEOChip select output for NJW1153 RadioFans.CN 收音机爱 好者资料库 13 RadioFans.CN 收音机爱 好者资料库 14 2. Block Diagram Program/Data RAM 192K Bytes 192 256 Program/Data ROM Page1 256K Bytes 256 256 256K Bytes ROM Page3 Program/Data Program/Data ROM Page2 256K Bytes 3232 DMPPMP CSP32 256 Program Cache 32K Bytes 64 D1 Data R/W R/W Data D2 64 256 Program FetchINTI/O C67x+ CPU Memory Controller 32 HighPerformance Crossbar Switch 32 McASP DMA Bus JTAG EMU 32 32 32 32 32 32 32 Peripheral Configuration Bus EMIF 32 Events In 32 MAX1MAX0 32 CONTROL 32 Interrupts Out I/O dMAX McASP0 16 Serializers McASP1 6 Serializers McASP2 2 Serializers DIT Only SPI1 SPI0 I2C1 I2C0 RTI32 PLL Peripheral Interrupt and DMA Events 32 32 32 32 RadioFans.CN 收音机爱 好者资料库 3. Terminal Functions Table, the Terminal Functions table, identifies the external signal names, the associated pin/ball numbers along with the mechanicalpackage designator, the pin type(I,O, IO,OZ,orPWR),whetherthe pin/ball has anyinternal pullup/pulldown resistors,whether the pin/ballisconfigurableas an IO in GPIO mode, and a functional pin description.