Denon-DNX1500S-mix-sm维修电路原理图.pdf

PROFESSIONAL BUSINESS COMPANY TOKYO, JAPAN For purposes of improvement, specifications and design are subject to change without notice. Please use this service manual with referring to the operating instructions without fail. Some illustrations using in this service manual are slightly different from the actual set. 注意 前、 必読。本機、火災、感電、 対安全性確保、配慮 、法的電気用品安全法 、所定許可得製造。 従際、安全性維 持、記載 注意事項必守。 本機仕様性能改良、予告変更 。 補修用性能部品保有期間、製造打切後 8 年。 修理際、必取扱説明書参照上、作業行 。 本文中使用、説明都合上現物 多少異場合。 X0196V.03 DE/CDM 0711 SERVICE MANUAL DJ MIXER MODELJPE3E2EKE2AE1CEUT DN-X1500 ? DN-X1500S ? Ver. 3 Please refer to the MODIFICATION NOTICE. RadioFans.CN 收音机爱 好者资料库 2 DN-X1500/DN-X1500S Please heed the points listed below during servicing and inspection. Heed the cautions! Spots requiring particular attention when servicing, such as the cabinet, parts, chassis, etc., have cautions indicated on labels or seals. Be sure to heed these cautions and the cau- tions indicated in the handling instructions. Caution concerning electric shock! (1) An AC voltage is impressed on this set, so touching inter- nal metal parts when the set is energized could cause electric shock. Take care to avoid electric shock, by for ex- ample using an isolating transformer and gloves when servicing while the set is energized, unplugging the power cord when replacing parts, etc. (2)There are high voltage parts inside. Handle with extra care when the set is energized. Caution concerning disassembly and assembly! Though great care is taken when manufacturing parts from sheet metal, there may in some rare cases be burrs on the edges of parts which could cause injury if fingers are moved across them. Use gloves to protect your hands. Only use designated parts! The sets parts have specific safety properties (fire resis- tance, voltage resistance, etc.). For replacement parts, be sure to use parts which have the same properties. In particu- lar, for the important safety parts that are marked ! on wiring diagrams and parts lists, be sure to use the designated parts. Be sure to mount parts and arrange the wires as they were originally! For safety reasons, some parts use tape, tubes or other insu- lating materials, and some parts are mounted away from the surface of printed circuit boards. Care is also taken with the positions of the wires inside and clamps are used to keep wires away from heating and high voltage parts, so be sure to set everything back as it was originally. Inspect for safety after servicing! Check that all screws, parts and wires removed or discon- nected for servicing have been put back in their original posi- tions, inspect that no parts around the area that has been serviced have been negatively affected, conduct an insulation check on the external metal connectors and between the blades of the power plug, and otherwise check that safety is ensured. (Insulation check procedure) Unplug the power cord from the power outlet, disconnect the antenna, plugs, etc., and turn the power switch on. Using a 500V insulation resistance tester, check that the insulation re- sistance between the terminals of the power plug and the ex- ternally exposed metal parts (antenna terminal, headphones terminal, microphone terminal, input terminal, etc.) is 1M or greater. If it is less, the set must be inspected and repaired. Concerning important safety parts Many of the electric and structural parts used in the set have special safety properties. In most cases these properties are difficult to distinguish by sight, and using replacement parts with higher ratings (rated power and withstand voltage) does not necessarily guarantee that safety performance will be pre- served. Parts with safety properties are indicated as shown below on the wiring diagrams and parts lists is this service manual. Be sure to replace them with parts with the designat- ed part number. (1) Schematic diagrams . Indicated by the ! mark. (2) Parts lists . Indicated by the ! mark. Using parts other than the designated parts could result in electric shock, fires or other dangerous situations. SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. CAUTION CAUTION 、点検時注意願。 注意事項守！ 特注意必要個所 、部品、捺印注意事項 表示。 注意書取扱説明書 注意事項必守。 感電注意！ (1) 、交流電圧印加通電時 内部金属部触感電。従 通電時、絶縁使用手袋着 用、部品交換、電源抜感電 注意。 (2) 内部高電圧部分、通電時取扱 十分注意。 分解、組立作業時注意！ 板金部品端面、部品製造時充分管理 、 板金端面鋭利箇所有 、 部品端面触指動怪我場 合十分注意作業下。 手保護 手袋着用。 指定部品使用！ 部品難燃性耐電圧安全上特性持 。従交換部品、使用 同特性部品使用。特配線図、部品 表 ! 印指定安全上重要部品必指定 使用。 部品取付配線引、 元！ 安全上、絶縁材料使用、 基板浮取付部品。 内部 配線引発熱部品高圧部 品接近配慮、 必 元。 後安全点検！ 取外、部品、配線元 、 個所周辺劣化 点検、外部金属端子部 、電源刃間絶縁、安 全性確保確認。 （絶縁方法） 電源電源抜、 外、電源入。500V 絶縁抵抗計用 、電源端子外部露出金属部 端子、端子、端子、入力端子 間、絶縁抵抗値 M 以上確認 。値以下点検修理必要。 安全上重要部品 本機使用多電気部品、 機構部品安全 上、 特別特性持。 特性場合、 外観判別、部品高定格（定 格電力、耐圧）持使用安全性維持 、限。安全上特性持部品、 配線図、 部品表表示 必指定部品番号使用願 。 (1) 配線図 ! 表示。 (2) 部品表 ! 表示。 指定部品異使用場合 、感電、火災危険生恐 。 注意 注意 RadioFans.CN 收音机爱 好者资料库 DN-X1500/DN-X1500S 3 各部 （組立、逆順序行。 ） 1. Top Panel Unit (1) 側面側 9 本、Top Panel Unit 引出 。 (2) FFC 。 (3) Top Panel Unit 。 （注）FCC 破損斜抜 下。 FFC 抜前 AC 電源 抜下。AC 接 続、Unit 電源供給危険。 2. Cross Fader Unit (1) Cross Fader Plate 取付上面 2 本 、Cross Fader Unit 引出。 (2) 。 DISASSEMBLY (Follow the procedure below in reverse order when reassem- bling.) 1. Top Panel Unit (1) Remove 9 side screws and pull up the Top Panel Unit. (2) Disconnect FFC cable and Connector. (3) Detach Top Panel Unit Note : Do not pull out aslant to prevent FFC cable damage. Do not fail to pull AC cord from wall outlet before dis- connect the FFC cable. If AC cord is remained plugged into wall outlet, power is kept supplied in the unit, which may cause danger. 2. Cross Fader Unit (1) Remove 2 top screws and pull up Cross Fader Unit. (2) Disconnect Connector. Top Panel Unit Cross Fader Unit Connector DN-X1500/DN-X1500S 4 3. CH Fader Unit (1) Remove 4 knobs. (2) Remove 4 screws and pull up CH Fader Panel. (3) Remove 2 screws for each CH. (4) Disconnect Connector. (5) Detach CH Fader Unit. 4. Top Panel (1) Pull out the knobs. (2) Remove 8 screws. (3) Detach Top Panel. SENSOR LEVER Top Panel 3. CH Fader Unit (1) 4 個。 (2) 4 本、CH Fader Panel 引出。 (3) 各 CH 2 本。 (4) 。 (5) CH Fader Unit 。 4. Top Panel (1) 。 (2) 8 本。 (3) Top Panel 。 DN-X1500/DN-X1500S 5 ADJUSTING THE MOVEMENT OF THE CROSS FADER CONTROL (1) Move the Cross Fader control all the way to the end in the direction of the arrow. (2) Turn Cross Fader screw A gently using the adjustment screwdriver to adjust the movement of the control. When turned clockwise, the movement of the control becomes heavier. When turned counterclockwise, the movement of the control becomes lighter. (3) After adjusting, mount the Cross Fader Unit onto the main unit, being sure to place the cable properly. Be careful not to let the cable get stuck in the main unit. Note : The Cross Fader has a precision structure. Do not tighten or loosen it excessively. Doing so could cause malfunction or adversely affect performance. 調整用 adjustment screwdriver screw A CROSS FADER 動調整 (1) Cross Fader 矢印方向一杯移動。 (2) Cross Fader A 調整用軽回 動調整。 右回、動重。 左回、動軽。 (3) 調整終了、整 Cross Fader Unit 本体取付。、本 体挟注意下。 （注）Cross Fader 精密構造、無 理締付行。故 障、性能影響与場合。 6 DN-X1500/DN-X1500S SERVICE MODE SPECIFICATION * How the product performs when the operation buttons for com control are pressed (including control input) is described in the table below. 1. POWER ON 2. CH GAIN VR 3. MASTER LEVEL VR 4. (SAMPLER) CROSSFADER ASSIGN switch FunctionDescriptionDisplayRemarks POWER (1)Turns power ON/OFF. Service Mode (2)Switches power OFF when ON. Enters in the service mode when power on while pressing MIC POST ON/OFF button and EFFECT LOOP ON/OFF but ton. For canceling the service mode, turn power off/on. Displays Service.Refer to CH GAIN VR. Refer to MASTER LEVEL VR. Refer to SAMPER ASSIGN. Refer to CROSSFADER ASSIGN. FunctionDescriptionDisplayRemarks CH LEVEL METER When you turn this VR, LED of CH level meter is lit. VR position is 0 : LED is not lit. VR position is 10 : All LED is lit. FunctionDescriptionDisplayRemarks MASTER LEVEL METER When you turn this VR, LED of master level meter is lit. VR position is 0 : LED is not lit. VR position is 10 : All LED is lit. FunctionDescriptionDisplayRemarks FL mode You can select FL display mode. A : FL tube is not lit. B : All FL tube is lit. POST : Displays VR checking or LED checking. 仕様 * 以下制御操作押（外部制御入力含）時本体動作記載。 1. POWER ON 2. CH GAIN VR 3. MASTER LEVEL VR 4. (SAMPLER) CROSSFADER ASSIGN switch 機能詳細表示備考 POWER (1) 電源 ON/OFF 。 (2)ON時、 電源OFF切替。 MIC POST ON/OFF EFFECT LOOP ON/OFF 押電源 ON 入。 取消、電源 OFF/ON 。 Service 表示。 CH GAIN VR 参照 MASTER LEVEL VR 参照 SAMPER ASSIGN 参照 CROSSFADER ASSIGN 参照 機能詳細表示備考 CH LEVEL METER VR 回、CH LED 点 灯。 VR 位置 0 時 : LED 消灯 VR 位置 10 時 : 全 LED 点灯 機能詳細表示備考 MASTER LEVEL METER VR 回、 LED 点灯。 VR 位置 0 時 : LED 消灯 VR 位置 10 時 : 全 LED 点灯 機能詳細表示備考 FL FL 表示選択 A : FL 管消灯 B : FL 管全点灯 POST : VR 中 LED 中表示 7 DN-X1500/DN-X1500S 5. SAMPLER ASSIGN switch 6. COM version check You can check the com version at Preset Functions. Please refer to the Instructions Manual. FunctionDescriptionDisplayRemarks FADER VR CHECK When CROSSFADER ASSIGN switch is set to POST, you can check the fader VR and LED. Refer to CROSSFAER ASSGIN. OFF When selected OFF, it becomes the LED off modde. Displays LED OFF. CH1 When selected CH1, it becomes the mode of reading/displaying CH1 fader VR value. Displays 0 100. Fader position is 0 : 0 Fader position is 10 :100 CH2 When selected CH2, it becomes the mode of reading/displaying CH2 fader VR value. Displays 0 100. Fader position is 0 : 0 Fader position is 10 : 100 CH3 When selected CH3, it becomes the mode of reading/displaying CH3 fader VR value. Displays 0 100. Fader position is 0 : 0 Fader position is 10 : 100 CH4 When selected CH4, it becomes the mode of reading/displaying CH4 fader VR value. Displays 0 100. Fader position is 0 : 0 Fader position is 10 : 100 MAIN MIC When selected MAIN MIC, it becomes the LED on mode. Displays LED ON. MASTER When selected MASTER, it becomes the mode of reading/displaying crossfader VR value. Displays 0 100. Fader position is Left side : 0 Fader position is Right side : 100 5. SAMPLER ASSIGN switch 6. COM 確認 Preset Functions 確認。 取扱説明書参照。 機能詳細表示備考 FADER VR CHECK CROSS FADEASSIGN POST 側設定 、 VR LED 。 CROSSFAER ASSGIN 参照 OFF OFF 選択、LED 。 LED OFF 表示 CH1 CH1 選択、CH1 VR 値読 込 / 表示。 0 100 表示 位置時 : 0 位置 10 時 : 100 CH2 CH2 選択、CH2 VR 値読 込 / 表示。 0 100 表示 位置時 : 0 位置 10 時 : 100 CH3 CH3 選択、CH3 VR 値読 込 / 表示。 0 100 表示 位置時 : 0 位置 10 時 : 100 CH4 CH4 選択、CH4 VR 値読 込 / 表示。 0 100 表示 位置時 : 0 位置 10 時 : 100 MAIN MIC MAIN MIC 選択、LED 。 LED ON 表示 MASTER MASTER 選択、 VR 値読込 / 表示。 0 100 表示 位置左時 :0 位置右時 : 100 8 DN-X1500/DN-X1500S SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. 主半導体記載。汎用半導体記載省略。 ICs MN102H74D (IC101) MN102H74D Terminal Function 75 76 100 125 26 50 51 No.Pin NameSymbolI/ODET Int PUExtResIniFunction 1P50,WAIT_WAITI-PuH-HI R/W timing wait signal 2P51,_RE_RDO-PuH-Read signal 3P52,_WEL_WELO-PuH-Write signal 4P53,_WEH_DSP_REQO-ON-Hi-zHSystem DSP REQ signal 5P60,_CS0_CS0O-PuH-Chip select signal 1st address of Flash ROM: 6P61,_CS1_CS_DSPO-PuH-Chip select of expansion port 7P62,_CS2_HBRO-PuH-DSP select signal Host Interface 8P63,_CS3_DSP_ACKI-ON-Hi-z-System DSP ACK signal 9P64,TM0IO,_BREQ_BREQI-PuH- Panel ucom control: When DSP boot, system bus open. L: open 10P65,TM1IO,_BRACK_BRACKO-PuH-When bus open, L output. 11P66,_WR_DAC_RSTO-ON-HHReset of ADC, DAC, and DIT 12_WORD_WORDI-LL-Select width of data bit bus L: 16bit 13P20,A00A00A/O-ON-Hi-z-Address bus 14P21,A01A01A/O-ON-Hi-z-Address bus 15P22,A02A02A/O-ON-Hi-z-Address bus 16P23,A03A03A/O-ON-Hi-z-Address bus 17VddVdd-Power supply(+3.3V) 18P54,BOSC,SYSCLKRESERVE1O-ON-LHSignal for test 19VssVss-GND(0V) 20XIXI-Not used 21XOXO-Not used 22VddVdd-Power supply(+3.3V) 23OSCIOSCII-This Need 12MHz for USB communication 24OSCOOSCOO-Output OSCI 25MODEMODEI-HH- Mode set H: Memory expansion/single chip mode 26P24,A04A04A/O-ON-Hi-z-Address bus 27P25,A05A05A/O-ON-Hi-z-Address bus 28P26,A06A06A/O-ON-Hi-z-Address bus 29P27,A07A07A/O-ON-Hi-z-Address bus 30P30,A08A08A/O-ON-Hi-z-Address bus 31P31,A09A09A/O-ON-Hi-z-Address bus 32P32,A10A10A/O-ON-Hi-z-Address bus 33P33,A11A11A/O-ON-Hi-z-Address bus 34VddVdd-Power supply(+3.3V) 35P34,A12A12A/O-ON-Hi-z-Address bus 36P35,A13A13A/O-ON-Hi-z-Address bus 37P36,A14A14A/O-ON-Hi-z-Address bus 38P37,A15A15A/O-ON-Hi-z-Address bus Internal Pull Up is 1090 ( K ), Ave : 30 ( K ) 9 DN-X1500/DN-X1500S No.Pin NameSymbolI/O DET Int PUExtResIniFunction 39P40,A16A16A/O-ON-Hi-z-Address bus 40P41,A17A17A/O-ON-Hi-z-Address bus 41P42,A18A18A/O-ON-Hi-z-Address bus 42P43,(TM2IO),A19A19A/O-PuH- Address bus Need pull up to extension for DSP boot control 43VssVss-GND(0V) 44P44,(TM3IO),A20_CDDEC_LCO-ON-Hi-zHLatch to codec1 L: available 45P45,(TM4IO),A21_CDDEC_LCO-ON-Hi-zHLatch to codec2 L: available 46P46,(TM5IO),A22_DAC_CSO-ON-Hi-zHDAC chip select L: available 47P47,_CS0S,(TM6IO),A23_DIT_CSO-PdLH DIT chip select L: available (be pull down in DSP) 48P70,_CS1S,(TM7IO),SBI3DIT_DINI-ON-Hi-zHDIT data input 49P71,_CS2S,(TM8IO),SBO3CLOCK_AO-PdLL CODEC(AD1838A)/DAC(PCM1791A)/DIT(AK4103) data output clock signal 50P72,_CS3S,(TM9IO),SBT3DATA_AO-ON-Hi-zL CODEC(AD1838A)/DAC(PCM1791A)/DIT(AK4103) data signal 51P80,TM10IOA,WDOUTPLGIN_LI-PuHH Lch SEND/RETURN connection status H: connect 52P81,TM10IOB,STOPPLGIN_RI-PuHH Rch SEND/RETURN connection status H: connect 53USBMODEUSBMODE-USB mode selectable terminal, connect to GND 54VddVdd-Power supply(+3.3V) 55D+D+-Pu- Connect USB terminal D+. 24 resistance is connected in series. 56D-D- Connect USB terminal D-. 24 resistance is connected in series. 57VssVss-GND(0V) 58P82,SBI2RxDI-PuH-75000bps Need to convert level 59P83,SBO2,TM11IOATxDO-PuHH75000bps Need to convert level 60P84,SBT2,TM11IOB_MONOI-ON-Hi-z-MONO/STEREO SW L: MONO 61VssVss-GND(0V) 62P90,AN0,TM12IOAATTIAd-Adjust VR for Master output (BAL/UNBAL) 63P91,AN1,TM12IOB_STB_CLRO-PdLL TC94A32/TC9162 ALL STB set to L L: L set , CODEC reset 64P92,AN2,TM13IOACLOCK_BO-PdLL Electric VR(TC94A32)/SelectorTC9162 data output clock signal 65P93,AN3,TM13IOBDATA_BO-ON-Hi-zLElectric VR(TC94A32)/SelectorTC9162 data signal 66VddVdd-Power supply(+3.3V) 67PA0,SBI1,AN4_FPLAY1O-PuHHCh1 Fader PLAY output